M5STACK AtomS3RCam Programmable Controller Manual

M5STACK AtomS3RCam Programmable Controller

Iinkcukacha

• IMCU: ESP32-S3-PICO-1-N8R8 @ Xtensa dual-core 32-bit LX7, 240MHz
• Ubunakho boNxibelelwano: I-Wi-Fi, i-BLE, i-I2C yokwandiswa koluvo, i-emitter ye-infrared
• Umthamo woGcino oluletshezi: 8MB IFLESHI
• PSRAM Umthamo wokuGcina: 8MB PSRAM
• Ukwandiswa kwezibuko: I-HY2.0-4P interface, yokudibanisa kunye nokwandisa i-I2C sensors
• Ukunikezelwa kwamandla Voltage: 4.5 ~ 5.5V DC
• Imilinganiselo: 24 x 24 x 13.5 mm
• Ubushushu bokusebenza: Ayichazwanga ngqo
• Ikhamera: Ikhamera yeGC0308, ixhasa ukuthathwa komfanekiso weVGA

Imiyalelo yokusetyenziswa kwemveliso

Ukuqalisa ngokukhawuleza-Shicilela ulwazi lwe-WiFi

1. Vula i-Arduino IDE (Jonga ku Isikhokelo sokuFakelo se-Arduino IDE yebhodi yophuhliso kunye nesoftware)
2. Cinezela kwaye ubambe iqhosha lokuseta kwakhona imizuzwana emi-2 kude kuvuleke ukukhanya okuluhlaza
3. Khetha ibhodi yeModyuli ye-ESP32S3 kunye ne-port ehambelanayo, uze ulayishe ikhowudi
4. Vula i-serial monitor ukuze ubonise i-WiFi eskeniweyo kunye nolwazi lwamandla omqondiso

Ukuqalisa ngokukhawuleza-Shicilela ulwazi lwe-BLE

1. 1. Vula i-Arduino IDE (Jonga ku Isikhokelo sokuFakelo se-Arduino IDE yebhodi yophuhliso kunye nesoftware)

FAQ

• Q: Yintoni umthamo wombanetage yeAtomS3R Cam?
  • A: Unikezelo lwamandla voltagi-e efunekayo yi-4.5 ~ 5.5V DC.

UMXHOLO

I-AtomS3R Cam isilawuli esidibeneyo esicwangcisiweyo esisekelwe kwi-microcontroller ye-ESP32-S3. Ibandakanya umlawuli oyintloko we-ESP32-S3-PICO-1-N8R8, equkethe i-Wi-Fi kunye nokusebenza kwe-BLE, i-8MB kwi-FLASH yebhodi, kunye ne-8MB PSRAM. Umlawuli uxhotyiswe ngekhamera ye-GC0308, exhasa ukuthatyathwa kwesithombe se-VGA. Inonxibelelwano lwe-Type-C ye-onboard yonikezelo lwamandla kunye nokukhuphela i-firmware kunye ne-HY2.0-4P yokwandisa izibuko. Umzantsi wesixhobo ugcina izikhonkwane ze-GPIO ezi-6 kunye nezikhonkwane zamandla ukuze kube lula ukwandiswa. Imveliso ilinganisa kuphela i-24x24x13.5mm, iyenza ifaneleke kwiinkqubo ezahlukeneyo ezifakwe kwisixhobo esikrelekrele.

Ikhamera yeAtomS3R

1. Ubunakho boNxibelelwano:
   • UMlawuli oPhambili: ESP32-S3-PICO-1-N8R8
   • Unxibelelwano olungenazingcingo: Wi-Fi, BLE
   • Ukwandiswa koMsebenzi: I-interface ye-HY2.0-4P, ixhasa uxhulumaniso kunye nokwandiswa kweenzwa ze-I2C
2. Iprosesa kunye nokusebenza:
   • Imodeli yeProsesa: Xtensa LX7 (ESP32-S3-PICO-1-N8R8)
   • Umthamo wokuGcina: 8MB Flash, 8MB PSRAM
   • Izakhelo zokuSebenza kweProsesa: Xtensa® dual-core 32-bit LX7 microprocessor, ukuya kuma 240 MHz
3. Iinzwa:
   • Ikhamera: Ikhamera yeGC0308, ixhasa ukuthathwa komfanekiso weVGA
4. Izikhonkwane zeGPIO kunye neNdibaniselwano eCwangcisiweyo:
   • Grove Interface: Ixhasa uxhulumaniso kunye nokwandiswa kweenzwa ze-I2C
   • Izikhonkwane ezisezantsi: Amandla kunye ne-6 GPIO pin headers
5. Abanye:
   Ujongano Lwebhodi: Ujongano lwe-Type-C lokukhuphela inkqubo kunye nonxibelelwano olulandelelanayo
   Imilinganiselo yoMzimba: I-24x24x13.5 mm, ngasemva inika i-M2 screw hole yokunyuka

INGCACISO

Ubungakanani bemveliso

UKUQALA NGOKUKHAWULEZA

Shicilela ulwazi lwe-WiFi

1. Vula i-Arduino IDE (Jonga ku https://docs.m5stack.com/en/arduino/arduino_ide kwisikhokelo sofakelo sebhodi yophuhliso kunye nesoftware)
2. Cinezela kwaye ubambe iqhosha lokuseta kwakhona imizuzwana emi-2 kude kuvuleke ukukhanya okuluhlaza
3. Khetha ibhodi yeModyuli ye-ESP32S3 kunye ne-port ehambelanayo, uze ulayishe ikhowudi
4. Vula i-serial monitor ukuze ubonise i-WiFi eskeniweyo kunye nolwazi lwamandla omqondiso

Shicilela ulwazi lweBLE

1. Vula i-Arduino IDE (Jonga ku https://docs.m5stack.com/en/arduino/arduino_ide kwisikhokelo sofakelo sebhodi yophuhliso kunye nesoftware)
2. Cinezela kwaye ubambe iqhosha lokuseta kwakhona imizuzwana emi-2 kude kuvuleke ukukhanya okuluhlaza
3. Khetha ibhodi yeModyuli ye-ESP32S3 kunye ne-port ehambelanayo, uze ulayishe ikhowudi
4. Vula i-serial monitor ukuze ubonise i-BLE eskeniweyo kunye nolwazi lwamandla omqondiso

Isilumkiso seFCC

Isilumkiso seFCC:

Naluphi na uTshintsho okanye uhlengahlengiso olungavunywanga ngokucacileyo liqela elinoxanduva lokuthotyelwa lunokuphelisa igunya lomsebenzisi lokusebenzisa isixhobo.

Esi sixhobo sithobela inxalenye ye-15 yeMithetho yeFCC. Ukusebenza kuxhomekeke kwezi meko zimbini zilandelayo: (1) Esi sixhobo asinakubanga luphazamiseko luyingozi, kwaye (2) esi sixhobo kufuneka samkele naluphi na uphazamiseko olufunyenweyo, kubandakanywa uphazamiseko olunokubangela usetyenziso olungafunekiyo.

INQAKU ELIBALULEKILEYO:

Phawula: Esi sixhobo sivavanyiwe saza safunyanwa ukuba sithobela imida yesixhobo sedijithali soDidi B, ngokungqinelana nenxalenye ye-15 yeMithetho yeFCC. Le mida yenzelwe ukubonelela ngokhuseleko olufanelekileyo ekuphazamisekeni okuyingozi kwindawo yokuhlala.

Esi sixhobo sivelisa, sisebenzise kwaye sinokusasaza amandla amaza erediyo kwaye, ukuba asifakanga kwaye sisetyenziswa ngokuhambelana nemiyalelo, sinokubangela uphazamiseko oluyingozi kunxibelelwano lwerediyo. Nangona kunjalo, akukho siqinisekiso sokuba ukuphazamiseka akuyi kwenzeka kufakelo oluthile. Ukuba esi sixhobo sibangela uphazamiseko oluyingozi kunomathotholo okanye ulwamkelo lukamabonakude, olunokumiselwa ngokucinywa nokulayita isixhobo, umsebenzisi uyakhuthazwa ukuba azame ukulungisa uphazamiseko ngenye okanye ngaphezulu kwezi ndlela zilandelayo:

• Jongisa kwakhona okanye uhambise i-eriyali efumanayo. — Yandisa ukwahlukana phakathi kwesixhobo nomamkeli. — Qhagamshela isixhobo kwindawo yokuphuma kwisekethe eyahlukileyo kuleyo apho umamkeli aqhagamshelwe khona. — Qhagamshelana nomthengisi okanye igcisa likanomathotholo/kumabonakude ukuze ufumane uncedo.

INkcazelo yokuVela kwiMitha yeFCC:

• Esi sixhobo sithobela imida yokuvezwa kwemitha yeFCC emiselwe indawo engalawulwayo. I-SAR yavavanyelwa isixhobo kwimowudi enxitywayo emzimbeni, kwaye inokufikelela kumda weSAR weFCC.