Surenoo SMC0700B-800480 Uluhlu lwe MCU Ujongano lwe TFT LCD Imodyuli

IINKCUKACHA ZAJIKELELE

Into yolwazi ngokubanzi	Imixholo		Iyunithi
Ubungakanani bomboniso weLCD (diagonal)	7.0		intshi
Ulwakhiwo lwemodyuli	Umboniso weLCD + RTP Chukumisa + PCB   Umboniso weLCD + CTP Chukumisa + PCB		-
Uhlobo lokuBonisa i-LCD	TFT/UKUGQIBELA		-
Imowudi yokuBonisa i-LCD	Ngokuqhelekileyo uMhlophe		-
Viewing ulwalathiso	12 IXESHA		-
Grey inversion Direction	6 IXESHA
Ubungakanani bemodyuli (W×H×T)	185.00×105.00×8.45		mm
Indawo esebenzayo (W×H)	154.21×85.92		mm
Inani leepixels (Resolution)	800RGB×480		pixel
Ipixel inowuthi (W×H)	0.1926 × 0.1790		mm
LCD Driver IC	LT7381		-
Uhlobo loNxibelelwano lwemodyuli	LCD	I-MCU 16bit/8bit interface	-
	RTP	4-Wire Resistive Touch	-
	CTP	I-interface ye-IIC
Igalelo lemodyuli voltage	5.0V		V
Ukusetyenziswa kwamandla kwimodyuli	-		mW
Amanani oMbala	16.7M		-
Uhlobo lwesibane	I-LED emhlophe		-

IMILINGANISELO YAPHANDLE

IIMPAWU EZIPHAKAMILEYO EZIPHAKAMILEYO

Ipharamitha egqibeleleyo Amanqaku aphezulu	Uphawu	Min	Max	Iyunithi
Ubushushu bokusebenza	Phezulu	-20	70	℃
Ubushushu bokugcina	Tst	-30	80	℃
Ukufuma	RH	-	90%(Ubukhulu 60℃)	RH

Phawula: Amanqaku aphezulu ngokupheleleyo athetha ukuba imveliso inokumelana nexesha elifutshane, hayi ngaphezulu kweeyure ezingama-120. Ukuba imveliso lixesha elide lokumelana nale meko, ixesha lokuphila liya kuba lifutshane.

IIMPAWU ZOMBANE(IIMPAWU ZASEDC)

IParameter yeDC iimpawu	Uphawu	Min.	Chwetheza.	Max.	Iyunithi
PCB yokusebenza voltage	VCC5V	-	5.0	-	V
LCD I/O yokusebenza voltage	VDD	3.0	3.3	3.6	V
Igalelo voltage 'H' inqanaba	VIH	2	-	3.6	V
Igalelo voltage 'L' inqanaba	VIL	-0.3	-	0.8	V
Iziphumo voltage 'H' inqanaba	VOH	2.4	-	-	V
Iziphumo voltage 'L' inqanaba	UMQULU	-	-	0.4	V

IIMPAWU ZEBACKLIGHT

Into yokukhanya ngasemva  iimpawu	Uphawu	Min.	Chwetheza.	Max.	Iyunithi	Phawula
Phambili Voltage	Vf	8.4	9.3	9.9	V	Qaphela1
Phambili Ngoku	If	-	140	-	mA	-
Inani le-LED	-	-	7*3	-	Iqhekeza	-
Imowudi yoQhagamshelwano lwe-LED	P/S	-	Uthotho	-	-	-
Ubomi be-LED	-	-	10000	-	yure	Qaphela2

Phawula:

• Qaphela1: Ubonelelo lwe-LED Voltage ichazwa ngenani LED ku Ta=25℃ kwaye Ukuba=140mA.
• Qaphela2: Ubomi be-LED buchaza njengexesha eliqikelelweyo ukuya kuma-50% ukuthotywa kokukhanya kokuqala. Ubomi be-LED bunokwehliswa ukuba isebenza ukuba inkulu kune-140mA.

IIMPAWU ZE-ELECTRO-OPTICAL

Into ye-electro-optical iimpawu		Uphawu	Imeko	Min.	Chwetheza.	Max .	Iyunithi	Phawula	Phawula
Ixesha lokuphendula		Tr + Tf	θ=0 =0 Ta=25℃	-	25	40	ms	UMZOBO 1.	4
Umlinganiselo wokuthelekisa		CR		-	350	-	-	UMZOBO 2.	1
Ukufana kokukhanya		EMHLOPHE		-	80	-	%	UMZOBO 2.	3
Ukukhanya komphezulu		Lv		-	300	-	cd/m2	UMZOBO 2.	2
I-CIE (x, y) chromaticity	Mhlophe	Mhlophe x	θ=0 =0 Ta=25℃	-	0.310	-	-	UMZOBO 2.	5
		Mhlophe y		-	0.33	-
	Bomvu	Ebomvu x		-	0.587	-
		network kunye		-	0.331	-
	Luhlaza	Luhlaza x		-	0.344	-
		Luhlaza y		-	0.571	-
	Luhlaza	Blue x		-	0.146	-
		Luhlaza okwesibhakabhaka kunye		-	0.0092	-
Viewuluhlu lwe-angle	=90(12 ntsimbi)		I-CR  10	-	50	-	deg	UMZOBO 3.	6
	=270(6 ntsimbi)			-	70	-	deg
	=0(3 ntsimbi)			-	70	-	deg
	=180(9 ntsimbi)			-	70	-	deg
Umlinganiselo we-NTSC	-		-	-	50	-	%	-	-

1. Inqaku le-1. I-Contrast Ratio (CR) ichazwa ngokwezibalo ngale fomula ilandelayo. Ukufumana ulwazi oluthe vetshe jonga FIG 2.:
2. Qaphela 2. Ukukhanya komphezulu ngumphezulu weLCD ukusuka kumphezulu nazo zonke iipikseli ezibonisa ezimhlophe. Ngolwazi oluthe vetshe jonga i-FIG 2.
   Lv=I-Average Surface Luminance nazo zonke iipixels ezimhlophe (P1,P2,P3,P4,P5,P6,P7,P8,P9)
3. Qaphela 3. Ukufana kokukhanya komphezulu (WHITE) kumiselwa ngokulinganisa ukukhanya kwindawo nganye yovavanyo 1 ukuya kwisi-9, kwaye emva koko kwahlulwe elona khanyiso liphezulu lamanqaku ali-9 ekhanyisa ngobuncinane bokukhanya kwamanqaku asi-9. Ngolwazi oluthe vetshe jonga i-FIG 2.
4. Qaphela 4. Ixesha lokuphendula lixesha elifunekayo ukuze isiboniso sitshintshe ukusuka kuMhlophe ukuya kumnyama (Rise Time, Tr) kwaye ukusuka kumnyama ukuya kumhlophe (Ixesha lokubola, Tf). Ngolwazi olongezelelweyo jonga FIG 1.
5. Inqaku le-5. I-CIE (x, y) chromaticity ,Ixabiso lika-x,y limiselwa yikhusi esebenzayo kwindawo 5. Ngolwazi oluthe vetshe jonga FIG 2.
6. Inqaku le-6. Viewi-engile ye-engile yi-engile apho umlinganiselo wokuchasana mkhulu kunexabiso elithile. Kwimodyuli ye-TFT, ixabiso elithile lomlinganiselo wokuchasana ngu-10. Ii-engile zimiselwe umgca othe tye okanye umgca ongu-x kunye nomgca othe nkqo okanye u-y ohamba phambili ngokumalunga nomgca ongu-z oqhelekile kumphezulu weLCD. Ukufumana ulwazi oluthe vetshe jonga i-FIG 3.
7. Inqaku le-7. Kuba Viewi-angle kunye novavanyo lwexesha lokuphendula, idatha yokuvavanya isekelwe kwi-Autronic-Melchers's ConoScope. Series Instruments. Ngomlinganiselo wokuthelekisa, ukuKhanya komphezulu, ukufana koLuminance kunye neCIE, idatha yovavanyo isekelwe kwi-BM-7 yesixhobo sokujonga iifoto.
8. Inqaku le-8. Kuhlobo lwe-TN yohlobo lwemodyuli egqithiselayo ye-TFT, i-Grey scale reverse iyenzeka kwicala lendawo yolawulo viewing eng.

I-FIG.1. Inkcazo yeXesha lokuPhendula

UMZEKELO 2. Indlela yokulinganisa yoMahluko, ukukhanya komphezulu, ukufana kokukhanya,
CIE (x , y) chromaticity
A: H/6;
B: V/6;
H,V : Ubungakanani beNdawo eSebenzayo (AA).
Isixhobo sokulinganisa: BM-7; Ubungakanani bendawo yokukhanya=5mm, 350mm umgama ukusuka kumphezulu we-LCD ukuya kwilensi yesixhobo.

UMFANEKISO.3. Inkcazo ye viewing eng 

INKCAZELO YE-INTERFACE

LCD1 Interface Inkcazelo ye CTP

HAYI.	Sumqondiso	I/O	INKCAZO
1	CS	I	Chip khetha
2	RS	I	Idatha/umyalelo ukhethe
3	WR	I	Bhala uphawu lwestrobe
4	RD	I	Funda isiginali yestrobe
5	LCD_RST	I	Isiginali ye-LCD ye-RESET, Phantsi iyasebenza
6-21	DB0 ~ DB15	I/O	Ibhasi yedatha(D0:LSB; D15:MSB)
22	GND	Ukunikezwa Amandla	Umhlaba wamandla
23	BL_CTRL	I	Iphini yokulawula isibane
24-25	VULA	-	Akukho nxibelelwano
26-27	GND	Ukunikezwa Amandla	Umhlaba wamandla
28	I-VDD5V	Ukunikezwa Amandla	Igalelo laMandla eModyuli (5V isiHlophe.) (* note1)
29	NC	O	Akukho nxibelelwano
30	CTP_SDA	I	Ungeniso lweDatha ye-TP
31	CTP_INT	I	Isiphumo se-TP INT
32	NC	-	Akukho nxibelelwano
33	CTP_CS	I	I-TP Chip yokusetha kwakhona iphini
34	CTP_SCL	I	TP Clock Input

LCD2 Interface Inkcazelo ye CTP

HAYI.	Uphawu	I/O	INKCAZO
1-2	GND	Ukunikezwa Amandla	Umhlaba wamandla
3	CS	I	Chip khetha
4	RS	I	Idatha/umyalelo ukhethe
5	WR	I	Bhala uphawu lwestrobe
6	RD	I	Funda isiginali yestrobe
7	LCD_RST	I	Isiginali ye-LCD ye-RESET, Phantsi iyasebenza
8-23	DB0 ~ DB15	I/O	Ibhasi yedatha(D0:LSB; D15:MSB)
24	GND	Ukunikezwa Amandla	Umhlaba wamandla
25	BL_CTRL	I	Iphini yokulawula isibane
26-28	NC	-	Akukho nxibelelwano
29-30	I-VDD5V	Ukunikezwa Amandla	Igalelo laMandla emodyuli (5V isiHlophe.)
31	NC	O	Akukho nxibelelwano
32	CTP_SDA	I	Ungeniso lweDatha ye-TP
33	CTP_INT	I	Isiphumo se-TP INT
34	NC	-	Akukho nxibelelwano
35	CTP_RST	I	TP Chip Khetha iNgeniso
36	CTP_CLK	I	TP Clock Input
37	NC	I	Akukho nxibelelwano
38	NC	I	Akukho nxibelelwano
39-40	GND	-	Umhlaba wamandla

LCD1 / LCD2 iNkcazelo yeNdibaniselwano yeRTP

UKUBEKA IXESHA

8080 iMode eDityanisiweyo yoNxibelelwano lwexesha

Uphawu	Ipharamitha		Ukukala		Iyunithi	Phawula
			Min.	Max.
TCYC8	Ixesha lomjikelo		50	-	ns	I-tc lixesha elinye lewotshi yenkqubo: tc = 1/SYS_CLK
TCC8	I-Strobe Pulse Width		20	-	ns
TAS8	Ixesha lokuSeta idilesi		0	-	ns
TAH8	Ixesha lokubamba idilesi		10	-	ns
I-TDS8	Ixesha lokuSeka iDatha		20	-	ns
TDH8	Ixesha lokubamba idatha		10	-	ns
I-TACC8	Ixesha lokuFikelela kwiZiphumo zeDatha		0	20	ns
TOH8	Ixesha lokuBamba iMphumo yeDatha		0	20	ns

Bhalisa Bhala:

1. Idilesi Bhala: Bhala idilesi yeRejista. Umzekeloample, 00h okt REG[00h], 01h okt REG[01h], 02h okt REG[02h] ……
2. Idatha yokuBhala: Bhala iDatha kwiRejista

Bhalisa Funda:

1. Idilesi Bhala: Bhala idilesi yeRejista
2. Idatha yokuBhala: Funda iDatha kwiRejista
   Ibonisa iMemori (Display RAM) kulapho idatha yomfanekiso wescreen seTFT igcinwa khona,. Bamba ujongano kwaye ubhale idatha kwiDisplay RAM. Inkqubo yofikelelo Bonisa i-RAM ngolu hlobo lulandelayo:

Bonisa i-RAM Bhala:

1. Cwangcisa iiRejista eziSebenzayo zeefestile ngaphambi kokubhala nayiphi na idatha yomfanekiso.
2. Yenza irejista bhalela kwiGraphic R/W Position Register 0, REG[5Fh]).
3. Phinda inyathelo lesi-2 de ucwangcise yonke i Window eSebenzayo & neGraphic R/W Ulungelelwaniso lweNdawo.
4. Yenza idilesi ubhale ukhomba kwiRejista yeMemory Data Port (REG[04h])
5. Yenza idatha ibhala ukugcwalisa ifestile. Ubhalo ngalunye oluya kwiSibuko seDatha seMemori luyakwandisa ngokuzenzekelayo idilesi yememori yangaphakathi.

UKUTHEMBEKA IMEKO YOVAVANYO

Hayi.	Into yovavanyo	Imeko yoVavanyo
1	Ugcino lobushushu obuphezulu	80℃/120 iiyure
2	Ugcino lobushushu obuphantsi	-30 ℃/120 iiyure
3	Ubushushu obuphezulu bokusebenza	70℃/120 iiyure
4	Ubushushu obuphantsi bokusebenza	-20 ℃/120 iiyure
5	Ugcino lweCycle Cycle	-20℃(30min.)~25(5min.)~70℃(30min.)×10cycles
A,Ukuhlolwa emva kovavanyo: Ukuhlolwa emva kwe-2 ~ 4 iiyure zokugcina kwiqondo lokushisa, i-sampandiyi kuba nasiphako; Ø Iqamza lomoya kwiLCD; Ø I-Sealleak; Ø Ukungabonisi; Ø Amacandelo angekhoyo; Ø Ukuqhekeka kweglasi; Ø Okwangoku iphezulu kabini kunexabiso lokuqala. B,NONE Ø Uvavanyo samples kufuneka isetyenziswe kwinto enye yovavanyo. Ø Sample ubukhulu bento nganye yovavanyo yi-5 ~ 10pcs.  Ø Ikhrayitheriya yesigwebo sokungaphumeleli: Inkcazo eyiSisekelo, iNgcaciso yoMbane, i-Mechanical Characteristic, i-Optical Character.

INDLELA YOKUHLOLA

Olu lwazi lwenziwa ukuba lusetyenziswe njengomgangatho wokwamkelwa / ukukhatywa kwemilinganiselo yemveliso yemodyuli ye-TFT-LCD / IPS TFT-LCD, kwaye le ngcaciso isebenzayo kuphela kwimeko yokuba ubungakanani bemodyuli bulingana okanye budlula ngaphezu kwe-intshi ye-3.5.

Sample plan
Sampisicwangciso sokulala ngokwe-GB/T2828.1-2003/ISO 2859-1:1999 kunye ne-ANSI/ASQC
I-Z1.4-1993, inqanaba eliqhelekileyo 2 kwaye lisekelwe:
Isiphene esikhulu: AQL 0.65
Isiphene esincinci: AQL 1.5

Imeko yokuhlola
ViewUmgama wokuhlola izithambiso malunga ne-30cm enamehlo angenanto, kwaye phantsi kokusingqongileyo kwe-20 ~ 40W ukukhanya kokukhanya, zonke iindlela zokuhlola indawo.ample kufuneka ibe ngaphakathi kwe-45 ° ngokuchasene nomgca we-perpendicular. (Ubushushu obuqhelekileyo 20 ~ 25℃ kunye nokufuma okuqhelekileyo 60±15%RH)

Inkcazo yento yoHlolo.
Inkcazo yendawo yokuhlola kwi-LCD.

Indawo A: umlinganiswa/indawo yeDijiti
Indawo B: viewindawo ngaphandle koMmandla A (uMmandla A + uMmandla B=ubuncinane Viewindawo yokulala)
Zone C: Ngaphandle viewindawo (indawo engabonakaliyo emva kokuhlanganisana kwimveliso yomthengi)

Umzobo.1 Iindawo zokuhlola kwi-LCD
Qaphela: Njengomgaqo jikelele, iziphene ezibonakalayo kwi-Zone C zivumelekile, xa kungekho nkathazo kumgangatho kunye nokuhlanganiswa kwemveliso yomthengi.

Inkcazo yesiphene esibonakalayo

Ichaphaza eliqaqambileyo	Ngenxa yokulahlekelwa ngumsebenzi wonke okanye inxalenye, amachaphaza amabi e-pixel abonakala eqaqambile kwaye ubungakanani bungaphezulu kwe-50% yechaphaza elinye apho iphaneli ye-LCD ibonisa phantsi kwepateni emnyama.
ichaphaza elimnyama	Amachaphaza abonakala emnyama kwaye engatshintshwanga ubungakanani apho iphaneli ye-LCD iboniswa phantsi komfanekiso obomvu, oluhlaza, oluhlaza okwesibhakabhaka, okanye umfanekiso osulungekileyo omhlophe.

Isiphene esikhulu 

Into Hayi.	Izinto eziza kuba ihlolwe	Umgangatho wokuhlola	Ukuhlelwa yeziphene
1	Iziphene zokusebenza	1) Akukho mboniso 2) Bonisa ngokungaqhelekanga 3) Icala elithe nkqo nelithe tye alikho 4) Isiphaluka esifutshane 5) Ukusetyenziswa kwamandla ngokugqithisileyo 6)Isibane sangasemva akukho kukhanya, ukuqhwanyaza kunye nokukhanya okungaqhelekanga	enkulu
2	Akukho	Icandelo elingekho
3	Umda wesishwankathelo	Umzobo xa uwonke ngaphaya komzobo awuvumelekanga

Isiphene esincinci 

Iikhrayitheriya zokuthambisa iModyuli

Into Hayi.	Izinto eziza kuba ihlolwe	Umgangatho Wokuhlola	Ukuhlelwa yeziphene
1	Umahluko kwi-Spec.	Ayivumelekanga	Enkulu
2	Ukuxobula ipateni	Akukho pateni yesubstrate exobukayo kwaye iyadada	Enkulu
3	Iziphene zesoldering	Akukho soldering engekho	Enkulu
		Akukho bhulorho yokuthambisa	Enkulu
		Akukho soldering ebandayo	Mncinci
4	Ukuxhathisa isiphene kwi-PCB	I-foil yobhedu ebonakalayo (Φ0.5 mm okanye ngaphezulu) kwipatheni ye-substrate ayivumelekanga	Mncinci
5	FPC umnwe wegolide	Akukho kungcola, ukuphuka, i-oxidation ikhokelela kumnyama	Enkulu
6	Iplastiki yokukhanya ngasemva isakhelo	Akukho deformation, crack, breaking, backlight positioning column breaking, nick ecacileyo.	Mncinci
7	Ukumakisha ukuprinta isiphumo	Akukho kuphawula kumnyama, okungaphelelanga, ukuguqulwa okukhokelela ekungakwazini ukugweba	Mncinci
8	Ukunyuswa kwesinyithi Umcimbi welinye ilizwe	Akukho kunyuswa kwentsimbi yangaphandle (ayidluli kwi-Φ0.2mm)	Mncinci
9	Ibala	Akukho ibala ukonakalisa izithambiso kakubi	Mncinci
10	Ipleyiti iyatshintsha umbala	Akukho pleyiti ibunayo, irusa kwaye ibe nombala	Mncinci
11	1. Amalungu okukhokela	a. Icala lokuthengisa lePCB Solder ukwenza i 'Filet' macala onke okhokelayo. I-Solder akufanele ifihle ifom ekhokelayo ngokugqibeleleyo.	Mncinci
		b. Icala lezixhobo (kwimeko 'nge-PCB yomngxuma') ISolder ukufikelela kwicala leMicimbi yePCB.	Mncinci
	2. Iiphakheji ezisicaba	Nokuba 'Inzwane' (A) okanye 'iSitywina'(B) sesikhokelo kufuneka sigqunywe ngu- “Filet”. Ifomu yokukhokela izakuthathwa ngaphezulu kweSolder.	Mncinci
	3. Iitshiphusi	(3/2) H ≥h ≥(1/2) H	Mncinci
	4. Ibhola ye-Solder / I-Solder splash	a. Isithuba phakathi kwebhola ye-solder kunye ne-conductor okanye i-solder pad h ≥0.13 mm. Ubukhulu bebhola ye-solder d≤0.15 mm.	Mncinci
		b. Ubuninzi beebhola ze-solder okanye i-solder splashes ayikho ngaphezu kwe-5 kwi-600 mm2.	Mncinci
		c. Iibhola ze-Solder / ii-Splashes ze-Solder aziphuli ubuncinane bokukhutshwa kombane.	Enkulu

Amaxwebhu / Izibonelelo

Surenoo SMC0700B-800480 Uluhlu lwe MCU Ujongano lwe TFT LCD Imodyuli [pdf] Incwadi yokusebenzisa SMC0700BA3-800480, SMC0700B-800480 Series, SMC0700B-800480 Series MCU Interface TFT LCD Imodyuli, MCU Interface TFT LCD Imodyuli, TFT LCD Imodyuli, LCD Module, Imodyuli

Iimbekiselo

• Incwadi yokusebenzisa