I-SmartGen HMC4000RM yesiLawuli sokuBeka iliso esikude IsiKhokelo soMsebenzisi
Onke Amalungelo Agciniwe. Akukho nxalenye yolu papasho inokuphinda iveliswe nangaluphi na uhlobo (kuquka ukufotokopa okanye ukugcinwa nangaluphi na uhlobo ngendlela ye-elektroniki okanye ngenye indlela) ngaphandle kwemvume ebhaliweyo yomnini-copyright.
I-SmartGen inelungelo lokutshintsha imixholo yolu xwebhu ngaphandle kwesaziso sangaphambili.
Itheyibhile 1 Uguqulelo lweSoftware
| Umhla | Inguqulelo | Umxholo |
| 2017-08-29 | 1.0 | Ukukhutshwa koqobo |
| 2018-05-19 | 1.1 | Guqula umzobo wofakelo lwemilinganiselo. |
| 2021-04-01 | 1.2 | Guqula i-"A-phase power factor" echazwe kwiSikhusi sesi-4 seSiboniso seSkrini sibe "kwisigaba samandla se-C". |
| 2023-12-05 | 1.3 | Tshintsha lamp inkcazo yovavanyo;Yongeza imixholo kunye noluhlu lwesicwangciso separameter. |
PHEZULUVIEW
I-HMC4000RM isilawuli sokubeka iliso esikude sidibanisa ukufakwa kwedijithali, ukwenziwa kwamazwe ngamazwe kunye nobuchwepheshe bothungelwano olusetyenziselwa inkqubo yokubeka iliso ekude yeyunithi enye ukufezekisa imisebenzi yokuqala / yokumisa kude. Iyalingana nomboniso weLCD, kunye nojongano olukhethwayo lwesiTshayina/lwesiNgesi. Ithembekile kwaye kulula ukuyisebenzisa.
UKUSEBENZA KUNYE NEEMPAWU
Iimpawu eziphambili zezi zilandelayo:
- I-132 * 64 i-LCD ene-backbit, i-interface ekhethiweyo yesiTshayina / isiNgesi, kunye nokusebenza kweqhosha lokutyhala;
- Isixhobo se-acrylic esinescreen esilukhuni sisetyenziselwe ukukhusela isikrini esinemisebenzi emikhulu yokuxhathisa kunye nokuxhathisa imikrwelo;
- Iphaneli yeSilicone kunye namaqhosha anentsebenzo enkulu yokusebenza kwindawo ephezulu / ephantsi yobushushu;
- Qhagamshela kwisilawuli se-host nge-RS485 port ukufikelela kwi-remote start/stop control kwimowudi yokulawula kude;
- Ngenqanaba lokukhanya kwe-LCD (amanqanaba ama-5) iqhosha lokulungelelanisa, kukulungele ukusebenzisa kwiimeko ezahlukeneyo;
- Inqanaba lokhuseleko lokungangeni manzi IP65 ngenxa yokutywinwa kwerabha efakwe phakathi kwendawo ebiyelweyo yomlawuli kunye nefascia yephaneli.
- Iziqeshana zokulungisa isinyithi zisetyenziswa;
- Uyilo lwemodyuli, ukuzicima kweplastiki ye-ABS ebiyelweyo kunye nendlela yokufaka efakelweyo; ubungakanani obuncinci kunye nesakhiwo esincinci kunye nokunyuka okulula.
INGCACISO
Itheyibhile ye-2 yeTechnical Parameters
| Izinto | Umxholo |
| Ukusebenza kweVoltage | I-DC8.0V ukuya kwi-DC35.0V, unikezelo lombane olungaphazanyiswa. |
| Ukutya umbane | <2W |
| RS485 Unxibelelwano lweBaud Rate | 2400bps/4800bps/9600bps/19200bps/38400bps inokusetwa |
| Case Dimension | 135mm x 110mm x 44mm |
| Iphaneli yokusika | 116mm x 90mm |
| Ubushushu bokusebenza | (-25~+70)ºC |
| Ukufuma okusebenzayo | (20–93)%RH |
| Ubushushu boGcino | (-25~+70)ºC |
| Inqanaba loKhuseleko | Iphaneli yangaphambili IP65 |
| Ukuqina kweInsulation | Faka i-AC2.2kV voltage phakathi komthamo ophezulutagi-terminal kunye nevolthi ephantsitage-terminal;Umbane ovuzayo awukho ngaphezulu kwe-3mA ngaphakathi komzuzu omnye. |
| Ubunzima | 0.22kg |
UKUSEBENZA
Itheyibhile 3 Tyhala amaqhosha Inkcazo
| Iimpawu zomqondiso | Umsebenzi | Inkcazo |
 |
Yeka | Misa ukusebenzisa ijenereyitha kwimowudi yolawulo olude;amp uvavanyo); |
 |
Qala | Kwimowudi yolawulo olukude, cofa eli qhosha lizakuqala ukusetwa kwejenereyitha. |
 |
Dimmer + | Cofa eli qhosha ukwandisa ukukhanya kwe-LCD. |
 |
Dimmer - | Cofa eli qhosha ukunciphisa ukukhanya kwe-LCD. |
 |
Lamp Uvavanyo | Emva kokucofa eli qhosha, i-LCD igxininiswe ngomnyama kwaye zonke ii-LED kwiphaneli yangaphambili ziyakhanyiswa. Bamba kwaye ucinezele eli qhosha ukususa ulwazi lwe-alam lomlawuli wendawo. |
 |
Seta/Qinisekisa | Umsebenzi ukwimo yokulinda. |
 |
Phezulu/Yandisa | Cinezela eli qhosha ukuskrola isikrini phezulu. |
 |
Phantsi/Nciphisa | Cinezela eli qhosha ukuskrola isikrini ezantsi. |
IMIBONISO YEZIKRISTU
Itheyibhile yesi-4 Isiboniso seSkrini
| Isikrini soku-1 | Inkcazo |
| Ijenereyitha isebenzisa umboniso wesikrini | |
 |
Isantya senjini, iseti yejenereyitha UA/UAB voltage |
| Uxinzelelo lweoyile, amandla omthwalo | |
| Ubume benjini | |
| Ijenereyitha ikumboniso wesikrini sokuphumla | |
 |
Isantya senjini, ubushushu bamanzi |
| Uxinzelelo lwe-oyile, umthamo wombanetage | |
| Ubume benjini | |
| Isikrini se-2 | Inkcazo |
 |
Ubushushu bamanzi enjini, unikezelo lwamandla omlawuli |
| Ubushushu be-oyile ye-injini, umthamo wetshajatage | |
| Ixesha lilonke lokusebenza kwe-injini | |
| Iinzame zokuqalisa injini, imo yesilawuli ngoku | |
| Isikrini se-3 | Inkcazo |
 |
Ucingo voltage: Uab, Ubc, Uca |
| Isigaba voltage: Ua, Uc | |
| Layisha ngoku: IA, IB, IC | |
| Layisha amandla asebenzayo, layisha amandla asebenzayo | |
| Inqaku lamandla, ukuphindaphinda | |
| 4th Isikrini | Inkcazo |
 |
Amandla asebenzayo, amandla asebenzayo, umboniso wamandla obonakalayo |
| A-phase kW, A-phase kvar, A-phase kvA | |
| B-isigaba kW, B-isigaba kvar, B-isigaba kvA | |
| Isigaba se-kW, i-kvar yesigaba se-C, i-kvA yesigaba se-C | |
| A-isigaba amandla factor, C-isigaba amandla factor, C-isigaba amandla factor | |
| 5th Isikrini | Inkcazo |
 |
Amandla ombane aqokelelweyo asebenzayo |
| Amandla ombane asebenzayo aqokelelweyo | |
| 6th Isikrini | Inkcazo |
 |
Ngenisa igama lezibuko |
| Ubume bezibuko longeniso | |
| Igama lezibuko lemveliso | |
| Ubume bezibuko lemveliso | |
| inkqubo yexesha langoku | |
| 7th Isikrini | Inkcazo |
 |
Uhlobo lwe-alam |
| Igama le-alam | |
Phawula: ukuba akukho mboniso weeparamitha zombane, isikrini sesi-3, sesi-4, nesi-5 siya kukhuselwa ngokuzenzekelayo.
IPENEL YOLAWULO NOSEBENZA
IPENEL YOLAWULO
Umfanekiso we-1 HMC4000RM Iphaneli yangaphambili
PHAWULA: Inxalenye yomfanekiso wesibane sezibane:
Iimpawu zeAlam: ukudanyaza kancinane xa kusenzeka izilumkiso; i-flash ekhawulezayo xa ii-alam zokuvala zenzekile; isibane sicinyiwe xa kungekho zivusi.
Iimpawu zesimo: Ukukhanya kuyacinywa xa i-gen iseti ikwimo yokulinda; flash kanye ngesekhondi ngexesha lokuqalisa okanye ukuvala; ihlala ivuliwe xa ubaleka ngokwesiqhelo.
UKUQALA KUDE/YIMA UMSEBENZI
UMZEKELISO
Cinezela 
yomlawuli we-host HMC4000 ukungena kwimowudi yokulawula kude, emva kokuba imowudi yokulawula kude iyasebenza, abasebenzisi banokulawula ukude i-HMC4000RM ukuqala / ukuyeka ukusebenza.
UKUDE UKUQALA UKUHLELA
- Xa umyalelo wokuqalisa ukude uyasebenza, "Qala ulibaziseko" isibali-xesha siyaqaliswa;
- "Qala ukulibazisa" ukubala kuya kuboniswa kwi-LCD;
- Xa ukulibaziseka kokuqala kuphelile, i-preheat relay inika amandla (ukuba iqwalaselwe), "ukulibaziseka kwangaphambili XX s" ulwazi luya kuboniswa kwi-LCD;
- Emva kokulibaziseka okungentla, i-Fuel Relay inamandla, kwaye emva kwesibini emva koko, i-Start Relay ibandakanyeka. I-Genset ikrwelwe kangangexesha elibekiweyo. Ukuba i-genset iyasilela ukutshisa ngexesha lomzamo wokukrazula i-fuel relay kunye ne-relay yokuqalisa iyacinywa ngexesha lokuphumla elisekwe kwangaphambili; "Ixesha lokuphumla kwe-crank" liqala kwaye ulinde umzamo olandelayo we-crank.
- Ukuba olu landelelwano lokuqalisa luqhubeleka ngaphaya kwenani elimiselweyo lenzame, ulandelelwano lokuqalisa luya kupheliswa, kwaye Ukusilela ukuqalisa i-alarm yempazamo iya kuboniswa kwiphepha le-alam le-LCD.
- Kwimeko yomzamo ophumeleleyo we-crank, isibali-xesha se-"Safety On" siyasebenza. Kwakamsinya nje ukuba oku kulibaziseka kuphelile, ulibaziseko “lokuqala ungenzi nto” luyaqaliswa (ukuba luqwalaselwe).
- Emva kokuqalisa kokungenzi nto, umlawuli ungena kwi-hi-speed "Isilumkiso" sokulibaziseka (ukuba siqwalaselwe).
- Emva kokulibaziseka kwe-"Warning Up" kuphelile, i-generator iya kungena kwisimo sokuSebenza esiQhelekileyo ngokuthe ngqo.
REMOTE YIMA Ulandelelwano
- Xa umyalelo wokumisa kude uyasebenza, umlawuli uqalisa ukulibaziseka kwe-hi-speed "Ukupholisa" (ukuba iqwalaselwe).
- Nje ukuba oku kulibaziseka "Ukupholisa" kuphelelwe lixesha, "Yeka i-Idle" iyaqaliswa. Ngexesha "Yeka ukungenzi nto" Ukulibaziseka (ukuba kuqwalaselwe), i-relay engasebenziyo inamandla.
- Nje ukuba le "Stop Idle" iphelelwe lixesha, i-"ETS Solenoid Hold" iqala, kwaye nokuba ingayeki ngokupheleleyo iya kugwetywa ngokuzenzekelayo. I-ETS relay inikwe amandla ngelixa i-fuel relay ikhutshwa amandla.
- Nje ukuba le "ETS Solenoid Hold" iphelelwe lixesha, "Lindela Ukulibaziseka Ukuyeka" iqala. Ukuyeka ngokupheleleyo kuchongwa ngokuzenzekelayo.
- Ijenereyitha ibekwe kwimowudi yayo yokulinda emva kokuyeka kwayo ngokupheleleyo. Kungenjalo, ukusilela ukuyekisa i-alam kuyaqaliswa kwaye ulwazi lwe-alam oluhambelanayo luboniswa kwi-LCD (Ukuba i-alam imisiwe ngempumelelo emva kokuba i-alamu iqalisile, injini iya kungena kwimeko yokulinda)
UQHAGAMSHELO LWEENGCACISO
HMC4000RM isilawuli ngasemva uyilo lwepaneli:
Fig.2 Iphaneli yoMlawuli ngasemva
Uluhlu lwe-5 INkcazelo yoQhagamshelwano lweSitena
| Hayi. | Umsebenzi | Ubungakanani beCable | Phawula |
| 1 | B- | 2.5mm2 | Idityaniswe nenegative yonikezelo lwamandla. |
| 2 | B+ | 2.5mm2 | Idityaniswe ne-positive yonikezelo lwamandla. |
| 3 | NC | Ayisetyenziswanga | |
| 4 | NGABA uH | 0.5mm2 | Eli zibuko landisa ujongano lojongano kwaye lugcinwe okwethutyana.Umgca wokhuselo uyacetyiswa ukuba usetyenziswa. |
| 5 | NGABA L | 0.5mm2 | |
| 6 | INGABE iGround Common | 0.5mm2 | |
| 7 | RS485 Umhlaba oqhelekileyo | / | I-Impedance-120Ω ucingo olukhuselayo luyacetyiswa, lunomhlaba omnye-kuphela. Olu jongano lusetyenziswa ukunxibelelana nomlawuli womkhosi HMC4000. |
| 8 | RS485+ | 0.5mm2 | |
| 9 | RS485- | 0.5mm2 |
PHAWULA: Izibuko le-USB ngasemva yinkqubo yokuphucula izibuko.
UDIDI KUNYE NENKCAZELO YEMIGAQO YENKQUBO
Itheyibhile ye-6 imixholo kunye neeRange zokuSeta iParameter
| Hayi. | Into | Uluhlu | Ukuhlala kukho | Inkcazo |
| Ukusetwa kweModyuli | ||||
| 1 | Ireyithi ye-RS485 yeBaud | (0-4) | 2 | 0: 9600bps 1: 2400bps2: 4800bps 3: 19200bps 4: 38400bps |
| 2 | Misa kancinci | (0-1) | 0 | 0:2 Amasuntswana 1:1 bit |
ISICELO ESIQHELEKILEYO
Umzobo.3 HMC4000RM Umzobo weSicelo esiQhelekileyo
UKUFAKWA
UKULUNGISA IIClips
- Umlawuli yiphaneli eyakhelwe-ngaphakathi uyilo; ilungiswa ziziqeshana xa zifakiwe.
- Rhoxisa isikrufu sekliphu yokulungisa (jikela ngokuchasene newotshi) de ifike kwindawo efanelekileyo.
- Tsala ikliphu yokulungisa ngasemva (ngasemva kwemodyuli) uqinisekise ukuba iziqeshana ezimbini zingaphakathi kwiindawo zazo zokubeka ezabelwe zona.
- Jika izikrufu zekliphu zokulungisa ngokwewotshi zide zilungiswe kwindawo yolawulo.
PHAWULA: Kufuneka kuthathelwe ingqalelo ukuba ungaqini kakhulu izikrufu zokulungisa izikliphu.
IMILINGANISELO NGOKUPHELELEYO KUNYE NESIKWE
Umzobo.4 Imilinganiselo yeCase kunye nePanel Cutout
UKULUNGISA INGXAKI
Itheyibhile yesi-7 Ukusombulula ingxaki
| Ingxaki | Isisombululo Esinokubakho |
| Umlawuli akukho mpendulo ngamandla. | Jonga iibhetri zokuqalisa; Jonga iingcingo zoqhagamshelwano zomlawuli; Jonga ifyuzi yeDC. |
| Ukusilela konxibelelwano | Jonga ukuba udibaniso lwe-RS485 luchanekile;Jonga ukuba izinga lonxibelelwano lwe-baud kunye nokuyeka kancinci kuyahambelana. |
Amaxwebhu / Izibonelelo
 |
I-SmartGen HMC4000RM isiLawuli sokuJonga esikude [pdf] Incwadi yokusebenzisa I-HMC4000RM, i-HMC4000RM isiLawuli sokuJonga iRemote, isiLawuli sokubek'esweni, isiLawuli sokuJonga, isiLawuli |
