Imiyalelo yokusebenza
R47 – 4 Zone Programmer
Kubalulekile: Gcina olu xwebhu Lo mdwelisi wendawo emi-4 yenzelwe ukunika ON/OFF ulawulo lwemimandla emi-4, kunye nexabiso elongezelelweyo losetyenziso lokhuseleko lweqabaka kunye nokutshixa iphedi yamaqhosha.
ISILUMKO! Phambi kokuba uqalise, qhawula isixhobo kumbhobho oyintloko. Kukho iindawo ezithwala ii-mains voltage emva kwekhava. Ungaze uhambe ungajongwanga xa ivuliwe. (Thintela abangezongcali kwaye ngakumbi abantwana ekufumaneni ukufikelela kuyo.) Ungaze uyisuse le mveliso kwisiseko sombane. Nqamula kunikezelo lwee-mains xa kukho nawuphi na umonakalo kuwo nawaphi na amaqhosha. Musa ukusebenzisa izixhobo ezibukhali ukucofa naliphi na iqhosha.
Iisetingi zefektri
| Inkqubo: | 5/2D |
| Isibane sangasemva: | On |
| Iphedi yamaqhosha: | Ivuliwe |
| Ukhuseleko lweFrost | Valiwe |
Izicwangciso zenkqubo yefektri
|
5/2D | |||||
| P1 IYAQHUBEKA | P1 OFF | P2 IYAQHUBEKA | P2 OFF | P3 IYAQHUBEKA | P3 OFF | |
| Mvulo-Lwesihlanu | 6:30 | 8:30 | 12:00 | 12:00 | 16:30 | 22:30 |
| NgoMgqibelo-Ngelanga | 7:30 | 10:00 | 12:00 | 12:00 | 17:00 | 23:00 |
| Zonke iintsuku ezisi-7 | 7D | |||||
| P1 IYAQHUBEKA | P1 OFF | P2 IYAQHUBEKA | P2 OFF | P3 IYAQHUBEKA | P3 OFF | |
| 6:30 | 8:30 | 12:00 | 12:00 | 16:30 | 22:30 | |
| Yonke imihla | 24H | |||||
| P1 IYAQHUBEKA | P1 OFF | P2 IYAQHUBEKA | P2 OFF | P3 IYAQHUBEKA | P3 OFF | |
| 6:30 | 8:30 | 12:00 | 12:00 | 16:30 | 22:30 | |
Ukuseta ngokutsha umdwelisi wenkqubo
Kuyimfuneko ukucofa iqhosha le-RESET phambi kocwangciso lokuqala.
Eli qhosha libekwe emva kwesigqubuthelo kumphambili weyunithi.
Ukumisela umhla kunye nexesha
Yehlisa isigqubuthelo esingaphambili kwiyunithi.
Hambisa isikhethi sokutshintshela kwi-CLOCK SET indawo.
Cofa i 
or 
amaqhosha ukukhetha usuku. Cinezela 
Cofa i or amaqhosha ukukhetha inyanga. Cinezela
Cofa i or amaqhosha ukukhetha unyaka. Cinezela
Cofa i or amaqhosha ukukhetha iyure. Cinezela
Cofa i or amaqhosha ukukhetha umzuzu. Cinezela
Cofa i or amaqhosha ukukhetha 5/2D, 7D okanye 24H Cinezela
Umhla, ixesha kunye nomsebenzi zibekiwe ngoku. Hambisa umkhethi wokutshintsha kwindawo ethi RUN ukuze uqhube inkqubo, okanye kwiPROG SET indawo yokutshintsha isicwangciso senkqubo.
ON/OFF ukhetho lwexesha
Kukho iindlela ezi-4 ezikhoyo kulo mdwelisi wenkqubo ukuze abasebenzisi bakhethe kwisicelo sabo somntu ngamnye.
NGOKUZENZAKALELAYO Umdwebi wenkqubo usebenza 3 'ON/OFF' amaxesha ngosuku.
YONKE IMINI Umdwebi wenkqubo usebenza 1'ON/OFF' ngosuku.
Oku kusebenza ukususela kwixesha lokuqala ukuya kwixesha lesithathu OFF.
ON Umdwelisi wenkqubo uvuliwe ngokusisigxina. **KUVULA**
CIMA Umcwangcisi ucimile ngokusisigxina. **VUMA**
Yehlisa isigqubuthelo esingaphambili kwiyunithi. Ngokucinezela i 
iqhosha ungatshintsha phakathi kwe-AUTO / LONKE USUKU / ON / OFF kuMmandla woku-1
Phinda le nkqubo yeZone 2 ngokucinezela i 
iqhosha kunye neZone 3 ngokucinezela i 
iqhosha n kunye neZone 4 ngokucinezela i 
iqhosha.
Ukulungelelanisa izicwangciso zenkqubo
Yehlisa isigqubuthelo esingaphambili kwiyunithi.
Hambisa iswitsha yomkhethi kwindawo yePROG SET.
Ngoku ungacwangcisa uMmandla woku-1.
Cofa i or amaqhosha ukunyenyisa P1 NGEXESHA. Cinezela
Cofa i or amaqhosha ukunyenyisa P1 OFF ixesha. Cinezela
Phinda le nkqubo ukunyenyisa ON & OFF amaxesha kwi P2 & P3.
Cinezela kwaye uphinde le nkqubo ingentla ukulungelelanisa uMmandla wesi-2.
Cinezela kwaye uphinde le nkqubo ingentla ukulungelelanisa uMmandla wesi-3.
Cinezela kwaye uphinde le nkqubo ingentla ukulungelelanisa iZone 4
Xa kugqityiwe, susa umkhethi kwindawo ethi RUN.
Khuphela umsebenzi
Kopisha umsebenzi ungasetyenziswa kuphela ukuba umdwelisi ukwimo ye-7d.
Yehlisa isigqubuthelo kumphambili womdwelisi wenkqubo.
Hambisa iswitsha yomkhethi kwindawo yePROG SET.
Cwangcisa i-ON & OFF amaxesha osuku lweveki onqwenela ukukopa kulo.
Cofa i 
iqhosha le-2 imizuzwana. Ngosuku olulandelayo lweveki luya kuqalisa ukudanyaza.
Cofa i iqhosha lokukhuphela i-ON & OFF ukuza kuthi ga kulo mhla.
Cofa i iqhosha lokutsiba usuku.
ON & OFF amaxesha unokukhutshelwa kwiintsuku ezininzi ngokusebenzisa i iqhosha.
Cofa i iqhosha xa ukhuphelo lugqityiwe.
Xa kugqityiwe, susa umkhethi kwindawo ethi RUN
ReviewUkufaka useto lwenkqubo
Yehlisa isigqubuthelo esingaphambili kwiyunithi.
Hambisa iswitsha yomkhethi kwindawo yePROG SET.
Yehlisa isigqubuthelo esingaphambili kwiyunithi.
Hambisa iswitsha yomkhethi kwindawo yePROG SET.
Ngokucinezela oku kuya review Ngalinye kumaxesha o-ON/OFF kwi-P1 ukuya kwi-P3 kuMmandla woku-1.
Phinda le nkqubo kwakhonaview amaxesha o-ON/OFF eZone 2 ngokucofa uze ucinezele
Phinda le nkqubo kwakhonaview amaxesha o-ON/OFF eZone 3 ngokucofa uze ucinezele
Phinda le nkqubo kwakhonaview amaxesha o-ON/OFF eZone 4 ngokucofa uze ucinezele
Xa kugqityiwe, susa umkhethi kwindawo ethi RUN.
Ukunyusa umsebenzi
Lo msebenzi uvumela umsebenzisi ukuba andise ixesha le-ON kwi-1, i-2 okanye iiyure ze-3.
Ukuba izowuni onqwenela ukuBoost imiselwe ukuba IVIME, unendawo yokuyivula kangangeeyure ezi-1, ezi-2 okanye ezi-3.
Cofa iqhosha elifunekayo:
kwiZowuni 1, 
ngenxa Zone 2 kunye 
kwiZone 3 kanye, 
kuZone 4 kanye, kabini okanye kathathu ngokulandelelanayo
Ukurhoxisa umsebenzi we-boost, cinezela ngokulula iqhosha elifanelekileyo kwakhona.
Umsebenzi wangaphambili
Lo msebenzi uvumela umsebenzisi ukuba azise phambili ixesha elilandelayo lokutshintsha.
Ukuba indawo ngoku ibekwe ixesha lokuba OFF kwaye i-ADV icinezelwe, indawo iya kuvulwa kude kube sekupheleni kwexesha elilandelayo lokutshintsha.
Ukuba indawo ngoku ibekwe ixesha lokuba i-ON kwaye i-ADV icinezelwe, indawo iya kucinywa kude kube sekupheleni kwexesha elilandelayo lokutshintsha.
Cinezela 
kwiZowuni 1, 
ngenxa Zone 2 okanye 
kwiZowuni 3, 
yeZone 4
Ukurhoxisa umsebenzi weADVANCE, cinezela ngokulula iqhosha leADV elahlukileyo kwakhona.
Imo yeholide
Yehlisa isigqubuthelo esingaphambili kwiyunithi.
Hambisa isikhethi sokutshintshela kwindawo ethi RUN.
Cofa i 
iqhosha.
Umhla kunye nexesha langoku liya kudayitsha kwiscreen. Ngoku uyakwazi ukufaka umhla kunye nexesha oceba ukubuya ngalo.
Cofa i or amaqhosha ukulungelelanisa ixesha leholide elifunekayo.
Cofa i iqhosha.
Umcwangcisi ucinyiwe ngoku ngenani elikhethiweyo leentsuku.
Ngokucinezela i iqhosha kwakhona, oku kuzakucima indlela yeholide, ngaloo ndlela ibuyisela umdwelisi wenkqubo kwizicwangciso eziqhelekileyo.
Ukukhetha imo yokukhanya ngasemva
On
Kukho iisetingi ezimbini zokukhetha. Useto oluhlala luhleli lwasefektri LUVULIWE.
ON Isibane esingasemva sivuliwe ngokusisigxina.
I-AUTO Xa ucofa naliphi na iqhosha isibane esingasemva sihlala sivuliwe kangangemizuzwana eli-10.
Ukulungelelanisa i-backlight setting, yehlisa ikhava ngaphambili kwiyunithi.
Hambisa isikhethi sokutshintshela kwindawo ethi RUN.
Cofa i iqhosha kwimizuzwana eyi-5.
Cinezela nokuba i or amaqhosha ukukhetha ON okanye imo ye-AUTO.
Cofa i iqhosha
Ukutshixa iphedi yamaqhosha kunye nokuvula
Ivuliwe
Ukutshixa iphedi yamaqhosha, cofa uze ubambe i kwaye amaqhosha 5 imizuzwana.
iya kuvela kwiscreen. Iphedi yamaqhosha itshixiwe ngoku.
Ukuvula iphedi yamaqhosha, cofa uze ubambe i kwaye amaqhosha 5 imizuzwana.
izakunyamalala kwikhusi. Iphedi yamaqhosha ivuliwe ngoku.
Umsebenzi wokukhusela iFrost
Valiwe
Uluhlu olukhethiweyo 5 ~ 20°C. Lo msebenzi usetelwe ukukhusela imibhobho ekukhenkcezini okanye ukuthintela ubushushu begumbi eliphantsi xa umdwelisi wenkqubo ecwangciswe ukuba AYIVALE okanye icinyiwe ngesandla.
Ukhuseleko lweqabaka lunokwenziwa ngokulandela le nkqubo ingezantsi.
Hambisa isikhethi sokutshintshela kwindawo ethi RUN.
Cinezela zombini i kwaye amaqhosha emizuzwana emi-5, ukufaka imo yokukhetha.
Cinezela nokuba i or amaqhosha ukuvula okanye ukucima ukhuseleko kwiqabaka.
Cofa i iqhosha ukuqinisekisa.
Cinezela nokuba i or amaqhosha ukwandisa okanye ukunciphisa ofunekayo
indawo yokukhusela iqabaka.
Cofa i iqhosha lokukhetha.
Zombini AMANZI ashushu kunye neendawo zokufudumeza ziya kuvulwa xa kwenzeka ubushushu begumbi buwela ngaphantsi kwendawo yokukhusela iqabaka.
Xa ukhuseleko lweqabaka luvuliwe "Iqabaka" iya kubonakala kwisikrini.
Xa ukhuseleko lweqabaka lusebenza "Iqabaka" liya kudanya kwiscreen.
Ukusetha kwakhona okuyintloko
Yehlisa isigqubuthelo kumphambili womdwelisi wenkqubo.
Kukho iihenjisi ezine ezibambe isigqubuthelo endaweni.
Phakathi kweehinge ze-3 kunye ne-4 kukho umngxuma ojikelezayo.
Faka usiba lwebhola okanye into efanayo ukuze ulawule ukuseta ngokutsha umdwelisi wenkqubo.
Emva kokucofa iqhosha lokuseta ngokutsha, umhla kunye nexesha ngoku kuya kufuneka zicwangciswe ngokutsha.
I-EPH iLawula i-Ireland
technical@ephcontrols.com www.ephcontrols.com
I-EPH ilawula i-UK
technical@ephcontrols.co.uk www.ephcontrols.co.uk
20221107_R47_OpIns_P
Amaxwebhu / Izibonelelo
 |
EPH ULAWULO R47 4 Zone Programmer [pdf] Incwadi Yomyalelo I-R47 4 uMdwelisi weNdawo, i-R47 4, uMcwangcisi weNdawo, uMdwelisi weNkqubo |
 |
EPH ULAWULO R47 4 Zone Programmer [pdf] Incwadi yokusebenzisa I-R47 4 uMdwelisi weNdawo, i-R47 4, uMcwangcisi weNdawo, uMdwelisi weNkqubo |
 |
EPH ULAWULO R47 4 Zone Programmer [pdf] Isikhokelo soFakelo R47, R47 4 Zone Programmer, 4 Zone Programmer, uMdwelisi |
 |
EPH ULAWULO R47 4 Zone Programmer [pdf] Incwadi Yomyalelo I-R47 4 uMcwangcisi wendawo, i-R47, uMcwangcisi weNdawo yesi-4, uMcwangcisi weZowuni, uMcwangcisi |
