Danfoss Optyma Plus SW Ver. 3.7x Controller for Condensing Unit

Intshayelelo

Isicelo
Ulawulo lweyunithi oludityanisiweyo

Advantages

• Ukulawula uxinzelelo loxinzelelo ngokumalunga nobushushu bangaphandle
• Ulawulo lwesantya esiguquguqukayo seFan
• Ukuvula / ukuvala okanye ukulawulwa kwesantya esiguquguqukayo secompressor
• Ulawulo lwento yokufudumeza kwikhrankcase
• Ukusebenza komlawuli wemini / ebusuku
• Eyakhelwe-ngaphakathi umsebenzi iwotshi kunye nogcino amandla
• Unxibelelwano lwedatha ye-Modbus eyakhelwe-ngaphakathi
• Ukubeka iliso ubushushu bokukhutshwa td
• Ulawulo lolawulo lokubuya kwe-oyile kulawulo oluguquguqukayo lwesantya

Umgaqo

• Umlawuli ufumana umqondiso wokupholisa okufunwayo, kwaye emva koko uqalise i-compressor.
• Ukuba icompressor ilawulwa ngesantya esiguquguqukayo, uxinzelelo lokufunxa (luguqulelwe kwiqondo lokushisa) luya kulawulwa ngokwexabiso elimiselweyo lobushushu.
• Ukulawulwa koxinzelelo lweCondenser kwenziwa kwakhona ngokulandela umqondiso ovela kwinzwa yeqondo lokushisa kunye nereferensi emiselweyo. Umlawuli uya kuthi emva koko alawule umqhubi, ovumela ukuba ukushisa kwe-condensing kugcinwe kwixabiso elifunwayo. Umlawuli unokulawula kwakhona into yokufudumeza kwi-crankcase ukuze ioli igcinwe ihluke kwifriji.
• Ngobushushu bokukhutshwa okugqithisileyo, inaliti yolwelo iya kwenziwa isebenze kumgca wokufunxa (kwicompressors ngokhetho lwenaliti yolwelo).

Imisebenzi

• Ukulawulwa kobushushu bokunciphisa
• Ukulawula isantya fan
• Ukulawula / ukuvala okanye ukulawulwa kwesantya secompressor
• Ukulawulwa kwezinto zokufudumeza kwi-crankcase
• Isitofu solwelo kwizibuko le-economizer (ukuba kuyenzeka)
• Ukuphakamisa ireferensi yokulawula uxinzelelo lwe-condenser ngexesha lokusebenza ebusuku
• Ukuqala kwangaphandle/ukumisa nge-DI1
• Ukhuseleko lokusikwa luvulwe ngophawu olusuka kulawulo lokhuseleko oluzenzekelayo

Ireferensi yommiselo yokuthoba ubushushu

• Umlawuli ulawula iReference condensing, enenkcukacha umahluko phakathi kobushushu bokunciphisa kunye nobushushu be-ambient. Indawo yokubeka ireferensi ingaboniswa ngokucofa ngokufutshane kwiqhosha eliphakathi kwaye ilungelelaniswe neqhosha eliphezulu nelisezantsi. Isalathiso sinokuphakanyiswa ebusuku ukuvumela isantya esicothayo sabalandeli ukunciphisa ingxolo yabalandeli. Oku kwenziwa nge-night set back feature.
• Olu seto lunokutshintshwa ngaphandle kokungena kwimowudi yokucwangcisa ngoko ke kufuneka kuthatyathwe ukhathalelo ukuze ungalungelelanisi ngempazamo.

Imini/Ebusuku

• Umlawuli unomsebenzi wewotshi yangaphakathi otshintsha phakathi kokusebenza kwasemini nasebusuku.
• Ngexesha lokusebenza ebusuku, ireferensi iphakanyiswa 'Night offset' ixabiso.

Olu phawu lwemini/lobusuku lunokwenziwa lusebenze ngezinye iindlela ezimbini:

• Ngokusebenzisa isignali yokuvula/yokucima – DI2
• Ngonxibelelwano lwedatha.

Ukusebenza kwabalandeli

Umlawuli uya kulawula i-fan ukwenzela ukuba ukushisa kwe-condensing kugcinwe kwixabiso elifunwayo ngaphezu kweqondo lokushisa langaphandle.

Umsebenzisi unokukhetha kwiindlela ezahlukeneyo zokulawula fan:

• Ukulawulwa kwesantya sangaphakathi
  Apha i-fan ilawulwa ngesantya nge-terminal 5-6.
  Kwimfuno ye-95% nangaphezulu, i-relay kwi-terminal 15-16 iyasebenza, ngelixa i-5-6 ivaliwe.
• Ummiselo wesantya sangaphandle
  Kwiimoto ezinkulu ze-fan ezine-outlet yangaphakathi eyaneleyo, umgaqo wesantya sangaphandle unokuqhagamshelwa kwi-terminal 54-55. I-0 - 10 V isignali ebonisa isantya esifunekayo sithunyelwa ukusuka kweli nqanaba. I-relay kwi-terminal 15-16 iya kusebenza xa i-fan isebenza.
• Kwimenyu 'F17' umsebenzisi angachaza ukuba loluphi ulawulo olunokusetyenziswa.

Isantya sabalandeli ekuqaleni
Xa i-fan iphinda iqalwa emva kwexesha lokungenzi nto, iya kuqaliswa ngesantya esisetwe kwi-'Jog Speed' function. Esi santya sigcinwa imizuzwana eyi-10, emva koko isantya sitshintsha kwimfuno yommiselo.

Isantya sabalandeli kwimithwalo ephantsi
Kwimithwalo ephantsi phakathi kwe-10 kunye ne-30%, isantya siya kuhlala kuloo nto imiselwe kumsebenzi we-'FanMinSpeed'.

Isantya sabalandeli kumaqondo obushushu asezantsi

• Ukunqanda ukuqala rhoqo / ukumisa kumaqondo obushushu asezantsi apho amandla omqhubi aphezulu, ngaphakathi ampi-liification factor ithotyiwe. Oku kubonelela ngommiselo osulungekileyo.
• I-'Jog speed' nayo yehlisiwe kwindawo ukusuka kwi-10 °C kunye nokuhla ukuya kwi -20 °C.
• Kumaqondo obushushu angaphantsi kwe -20 °C ixabiso le-'Jog Low' lingasetyenziswa.

Compressor compartment pre-ventilation

• I-condenser fan iqala kwaye isebenze ixesha kunye nesantya ngaphambi kokuba icompressor iqale. Oku kwenzeka kwimeko yaso nasiphi na isikhenkcezisi esinokutsha esikhethwe nge-"o30 Refrigerant", ukufumana umoya okhuselekileyo ngelixa ufunxa igesi enokutsha ye-A2L-efrijini ngaphandle kwecompressor compartment.
• Kukho ukulibaziseka okusisigxina malunga nemizuzwana ye-8 phakathi kokungena komoya kwangaphambili kunye nokuqala kwecompressor ukuze kuncitshiswe ukuhamba komoya kakhulu kwaye kuthintelwe naziphi na iingxaki zokuxinana kumaqondo obushushu asezantsi.

Ulawulo lweCompressor

• Icompressor ilawulwa ngumqondiso kwigalelo le-DI1.
• Icompressor iya kuqala xa igalelo lixhunyiwe.

Izithintelo ezithathu ziphunyeziwe ukunqanda ukuqala/ukumisa rhoqo:

• Inye ngobuncinci NGEXESHA
• Inye ngexesha elincinci le-OFF
• Enye yeyokuba kufuneka kudlule ixesha elingakanani phakathi kweziqalo ezimbini.

Ezi zithintelo zintathu zinokubaluleka okuphezulu ngexesha lommiselo, kwaye eminye imisebenzi iya kulinda de igqitywe ngaphambi kokuba umgaqo uqhubeke. Xa icompressor 'itshixiwe' ngesithintelo, oku kunokubonwa kwisaziso sesimo. Ukuba igalelo le-DI3 lisetyenziswa njengento yokumisa ukhuseleko kwi-compressor, isignali yokungena eyaneleyo iya kumisa ngokukhawuleza i-compressor. Iicompressor zesantya eziguquguqukayo zinokulawulwa ngesantya ngevolthitagUmqondiso we-e kwimveliso ye-AO2. Ukuba le compressor isebenze ixesha elide ngesantya esiphantsi, isantya sonyuswa ixesha elifutshane ngenjongo yokubuya kweoli.

Ubushushu obuphezulu begesi yokukhupha

• Iqondo lobushushu lirekhodwa yi-sensor Td.
• Ukuba ulawulo lwesantya esiguquguqukayo sikhethwa kwi-compressor, olu lawulo luya kuqala ukunciphisa umthamo we-compressor ukuba ukushisa kwe-Td kusondela kwixabiso eliphezulu elibekiwe.
• If a higher temperature is detected than the set max. temperature, the fan’s speed will be set to 100%. If this does not cause the temperature to drop, and if the temperature remains high after the set delay time, the compressor will be stopped.
• The compressor will only be re-started once the temperature is 10 K lower than the set value. The above mentioned re-start restrictions must also be complete before the compressor can start once again.
• Ukuba ixesha lokulibaziseka limiselwe ku-'0', umsebenzi awuyi kumisa i-compressor. Inzwa ye-Td inokukhutshwa (o63).

Inaliti yolwelo kwizibuko le-economizer

• Umlawuli unokuvula inaliti yolwelo kwizibuko le-economizer ukuba ubushushu bokukhupha busondela kubushushu obuvumelekileyo.
• Phawula: Umsebenzi wenaliti yolwelo sebenzisa i-Aux Relay ukuba i-relay iqwalaselwe kulo msebenzi.

Ukujongwa koxinzelelo oluphezulu

• Ngexesha lolawulo, umsebenzi wangaphakathi wokubeka iliso kwixinzelelo oluphezulu uyakwazi ukubona ukunyanzeliswa koxinzelelo olungaphaya komda ukwenzela ukuba ummiselo uqhubeke.
• Nangona kunjalo, ukuba isethingi ye-c73 igqithisiwe, i-compressor iya kumisa kwaye i-alamu iqhutywe.
• Ukuba, ngakolunye uhlangothi, umqondiso uvela kwisiphaluka esiphazamisekileyo sokhuseleko esixhunywe kwi-DI3, i-compressor iya kumiswa ngokukhawuleza kwaye i-fan iya kusekwa kwi-100%.
• Xa isiginali kwakhona 'Kulungile' kwigalelo le-DI3, ummiselo uya kuqalisa kwakhona.

Ukujongwa koxinzelelo oluphantsi
Ngexesha lolawulo, umsebenzi wokubeka iliso ophantsi woxinzelelo uya kunqumla i-compressor xa ufumanisa uxinzelelo lokufunxa oluwela ngaphantsi komda ophantsi, kodwa kanye kuphela ubuncinci bexesha le-ON ligqithisiwe. Kuya kukhutshwa i-alam (A2). Lo msebenzi uya kuba lixesha lokulibaziseka, ukuba icompressor iqala kwiqondo lokushisa eliphantsi.

Umda wokumpompa phantsi
Icompressor iya kunqunyanyiswa ukuba uxinzelelo lokufunxa oluwela ngaphantsi kwexabiso elimiselweyo lubhalisiwe, kodwa kanye kuphela ubuncinane bexesha le-ON ligqithisiwe.

Ukufudumeza into kwikhrankcase

• Umlawuli unomsebenzi we-thermostat onokulawula into yokufudumala kwi-crankcase. Ngaloo ndlela ioli inokugcinwa yahlukile kwisikhenkcisi. Umsebenzi uyasebenza xa icompressor iyekile.
• Umsebenzi usekelwe kubushushu be-ambient kunye nobushushu berhasi yokufunxa. Xa amaqondo obushushu amabini elingana ± umahluko weqondo lobushushu, amandla aya kunikwa into yokufudumeza.
• Isicwangciso se-'CCH off diff' sibonisa xa amandla engasayi kuphinda anikezelwe kwizinto zokufudumeza.
• I-'CCH kwi-diff' ibonisa ukuba i-100% yamandla iya kuthunyelwa nini kwindawo yokufudumeza.
• Phakathi kwezicwangciso ezimbini umlawuli ubala i-wattage kwaye idibanisa into yokufudumeza kwi-pulse/pause cycle ehambelana ne-wat efunwayotage.
• Isivamvo seTaux singasetyenziswa ukurekhoda ubushushu kwikhrankcase ukuba uyafunwa.
• Xa i-sensor ye-Taux irekhoda iqondo lobushushu elingaphantsi kwe-Ts+10 K, i-elementi yokufudumeza iya kusekwa kwi-100%, kodwa kuphela ukuba ubushushu be-ambient bungaphantsi kwe-0 °C.

Ukwahlula umsebenzi we-thermostat
Inzwa ye-taux ingasetyenziselwa umsebenzi wokufudumeza kunye nobushushu obunocwangciso. Apha, i-AUX relay iya kudibanisa into yokufudumala.

Amagalelo edijithali
Kukho amagalelo amabini edijithali i-DI1 kunye ne-DI2 enomsebenzi woqhagamshelwano kunye ne-digital input DI3 enevolthi ephezulutage umqondiso.

Zingasetyenziselwa le misebenzi ilandelayo:

• DI1: Iqala kwaye iyeke icompressor
• DI2: Apha umsebenzisi unokukhetha kwimisebenzi eyahlukeneyo
  • Umqondiso ovela kumsebenzi wokhuseleko lwangaphandle
  • Iswitshi ephambili yangaphandle / isignali yokubuyela umva ebusuku / umsebenzi we-alamu owahlukileyo / Ukubekwa esweni kwesiginali yegalelo / isiginali evela kulawulo lwesantya sangaphandle
• DI3: Isignali yokhuseleko ukusuka kwiswitshi ephantsi / ephezulu yoxinzelelo

Unxibelelwano lwedatha

• Umlawuli uhanjiswa nge-MODBUS yonxibelelwano lwedatha eyakhelweyo.
• Ukuba kucelwe uhlobo olwahlukileyo lonxibelelwano lwedatha, imodyuli ye-LON RS-485 inokufakwa kumlawuli.
• Uqhagamshelo luya kwenziwa kwi-terminal RS 485. Kubalulekile
• Lonke unxibelelwano kunxibelelwano lwedatha kufuneka luhambelane neemfuno zeentambo zonxibelelwano lwedatha.
• Jonga uncwadi: RC8AC.

Bonisa

• Umlawuli uneplagi enye yokubonisa. Apha bonisa uhlobo EKA 163B okanye EKA 164B (ubuninzi. ubude 15 m) inokudityaniswa.
• I-EKA 163B sisiboniso sokufunda.
• I-EKA 164B yeyokufunda nokusebenza.
• Umdibaniso phakathi kwesibonisi kunye nomlawuli kufuneka ube nentambo eneplagi kuzo zombini iziphelo.
• Ulungiselelo lunokwenziwa ukuqinisekisa ukuba i-Tc okanye i-Ts iza kufundwa. Xa ixabiso lifundwa, ukufundwa kwesibini kunokuboniswa ngokucinezela ngokufutshane iqhosha elisezantsi.
• Xa isiboniso siza kudityaniswa ne-MODBUS eyakhelwe-ngaphakathi, isiboniso sinokuba ne-advantagngokufanelekileyo itshintshwe ibe kolunye uhlobo olufanayo, kodwa nge-Index A (uguqulelo olunezikrufu iitheminali).
• Idilesi yabalawuli kufuneka ibekwe phezulu kuno-0 ukwenzela ukuba umboniso ukwazi ukunxibelelana nomlawuli.
• Ukuba uxhulumaniso lweziboniso ezimbini lufunekayo, enye kufuneka idibaniswe kwiplagi (ubuninzi be-15 m) kwaye enye kufuneka idibaniswe nonxibelelwano lwedatha esisigxina.

Bhala ngaphezulu
Umlawuli uqulethe imisebenzi enokusetyenziswa kunye nomsebenzi ogqithisiweyo kumphathi wesango/umphathi wenkqubo.

Umsebenzi ngokusebenzisa idatha unxibelelwano	Ishedyuli yosuku / yobusuku
Umsebenzi in gateway/system umphathi	Ulawulo lwemini / lobusuku / ishedyuli yexesha
Isetyenzisiwe iiparamitha in Optyma™ Ukongeza	- Ukubuyela umva ebusuku

Uvavanyo lwemisebenzi

Umsebenzi	IPara- imitha	Ipharamitha by ukusebenza ngokusebenzisa idatha unxibelelwano
Okuqhelekileyo umboniso
Umboniso ubonisa ixabiso lobushushu loxinzelelo lokufunxa i-Ts okanye ukusuka kuxinzelelo lokujiya Tc. Faka ukuba yeyiphi kwezi zibini eziza kuboniswa kwi-o17. Ngethuba lokusebenza, xa enye yezi zibini iboniswa kwisiboniso, elinye ixabiso lingabonwa ngokucinezela kunye nokubamba iqhosha elisezantsi.		Ts / Tc
Thermostat		Thermostat ulawulo
Seta inqaku Isalathiso somlawuli i-Tc bubushushu bangaphandle + indawo yokubeka + nayiphi na i-offset esebenzayo. Ngenisa indawo emiselweyo ngokucofa iqhosha eliphakathi. I-offset ingangeniswa nge-r13.		Isalathiso
Iyunithi Set here if the display is to show SI-units or US-units 0: SI (°C and bar) 1: US (°F and Psig).	R05	Iyunithi °C=0. / °F=1 (Kuphela °C kwi-AKM, nokuba sithini na isicwangciso)
Qala / Yeka of ifriji Ngolu seto ifriji inokuqaliswa, iyeke okanye ugqithiso lwesandla lweziphumo lunokuvunyelwa. (Kulawulo lwemanuwali ixabiso limiselwe ku--1. Emva koko ii-relay outlets zinganyanzeliswa- zilawulwe ngokwemilinganiselo yokufunda (u58, u59 njl.). Apha ixabiso lokufunda lingabhalwa ngaphezulu.) Ukuqala / ukumiswa kwefriji kunokufezekiswa kunye nomsebenzi wokutshintsha wangaphandle odityaniswe kwigalelo le-DI. Ukuba umsebenzi wokutshintsha wangaphandle awukhethwanga, igalelo kufuneka lifutshane. Isikhenkcisi esimisiweyo siya kunika "i-alam yokulinda".	R12	Utshintsho oluphambili 1: Qala 0: Yeka -1: Ulawulo lwezandla lweziphumo ezivumelekileyo
Busuku ukubuyisela umva ixabiso Isalathiso somlawuli siphakanyiswa ngeli xabiso xa umlawuli etshintshela ekusebenzeni ebusuku.	R13	Ukunciphisa ebusuku
Isalathiso Ts Apha ireferensi ifakwe kuxinzelelo lokufunxa i-Ts kwiidigri (kuphela kwi-Optyma™ Ukongeza kwi-inverter)	R23	Ts Ref
Isalathiso Tc Apha ireferensi yomlawuli wangoku yoxinzelelo loxinzelelo lwe-Tc inokufundwa ngeedigri.	R29	Tc Ref
Ngaphandle ukufudumeza umsebenzi Ixabiso le-Thermostat lokusika kwi-indawo yokufudumeza yangaphandle (kuphela xa 069=2 kunye ne-o40=1) I-relay iyasebenza xa ubushushu bufikelela kwixabiso elimiselweyo. I-Relay ikhupha kwakhona xa iqondo lokushisa liye landa nge-5 K (umahluko ubekwe kwi-5 K).	R71	Aux Ther Ref
Ubuncinci bobushushu bokujiya (esona singqinisiso sommiselo esivumelekileyo esisezantsi) Apha esona salathisi sivumelekileyo singeniswa ukwenzela ubushushu obuphantsi Tc.	R82	Min Cond Temp
Ubushushu obuphezulu bokujiya (eyona salathiso siphezulu esivunyelweyo sommiselo) Apha esona salathiso siphezulu sivumelekileyo singeniswa ukwenzela ubushushu obuphantsi Tc.	R83	Max Cond Temp
Ubushushu obuphezulu begesi yokukhupha Apha ubushushu obuphezulu obuvunyelweyo bokukhupha igesi bungeniswa. Ubushushu bulinganiswa ngesinzwa Td. Ukuba iqondo lokushisa ligqithisiwe, i-fan iya kuqaliswa kwi-100%. Isibali-xesha sikwaqalisiwe esinokusetwa kwi-c72. Ukuba isicwangciso sexesha siphelile, icompressor iya kunqunyanyiswa kwaye i-alamu iya kukhutshwa. Icompressor iya kudityaniswa kwakhona nge-10 K ngaphantsi komda wokusika, kodwa emva kokuba icompressor off timer iphelelwe lixesha.	R84	Max Disch Temp
		Ubusuku obuthile (ukuqala komqondiso wasebusuku. 0=Usuku, 1=Ubusuku)
Ialarm		Ialarm izicwangciso
Umlawuli unokunika i-alamu kwiimeko ezahlukeneyo. Xa kukho i-alam zonke ii-diode ezikhupha ukukhanya (i-LED) ziya kudanyaza kwiphaneli engaphambili yesilawuli, kwaye isilayidi se-alam siya kusikwa.		Ngonxibelelwano lwedatha ukubaluleka kwee-alamu zomntu ngamnye kunokuchazwa. Ukuseta kuqhutywa kwimenyu ye "Alarm destinations" nge-AKM.
Ukulibazisa of a DI2 ialam Igalelo lokusika/ukusika liya kubangela i-alam xa ukulibaziseka kwexesha kudlulile. Umsebenzi uchazwe kwi-o37.	A28	AI. Delay DI2
Phezulu ukujiya ubushushu ialam umda Umda weqondo lobushushu lokujiya, usete njengomahluko ngaphezu kwereferensi ekhawulezileyo (iparamitha r29), apho iAlarm ye-A80 ivulwe emva kokulibaziseka okuphelelweyo (jonga iparamitha A71). IParameter iseti kuKelvin.	A70	Air flow Diff
Ixesha lokulibazisa le-alam ye-A80 - jonga kwakhona ipharamitha A70. Misela kwimizuzu.	A71	Ukuhamba komoya del
		Seta kwakhona ialam
		Ctrl. Impazamo

Isicompressor		Isicompressor ulawulo
Ukuqala/ukumisa komlawuli kunokuchazwa ngeendlela ezininzi. Ngaphakathi kuphela: Apha, kuphela iswitshi engundoqo yangaphakathi ku-r12 esetyenziswayo. Ngaphandle: Apha, igalelo le-DI1 lisetyenziswa njengokutshintsha kwe-thermostat. Ngolu seto, igalelo le-DI2 lingachazwa njengesixhobo 'sokhuseleko lwangaphandle' esinokumisa isicinezeli.
Amaxesha okubaleka Ukuthintela ukusebenza ngokungaqhelekanga, amaxabiso anokumiselwa ixesha lokuba icompressor isebenze xa sele iqalisiwe. Kwaye ixesha elingakanani ubuncinane kufuneka limiswe.
Min. NGEXESHA (ngemizuzwana)	c01	Min. Ngexesha
Min. OFF-ixesha (ngemizuzwana)	c02	Min. Ixesha lokuphumla
Ubuncinane ixesha phakathi ukusikwa of udluliselo (ngemizuzu)	c07	Ixesha lokuqalisa kwakhona
Impompo phantsi Umda Ixabiso loxinzelelo apho icompressor iyeka	c33	PumpDownLim
Isicompressor imiz. isantya Apha ubuncinci besantya esivumelekileyo secompressor sibekiwe.	c46	CmpMinSpeed
Isicompressor qala isantya Icompressor ayiyi kuqala ngaphambi kokuba isantya esifunekayo sifumaneke	c47	CmpStrSpeed
Isicompressor max. isantya Umda ophezulu wesantya secompressor	c48	CmpMaxSpeed
Isicompressor max. isantya ngexesha busuku ukusebenza Umda ophezulu wesantya secompressor ngexesha lokusebenza ebusuku. Ngethuba lokusebenza ebusuku, ixabiso le-c48 liyancipha ukuya kwipesentitagixabiso libekwe apha	c69	CmpMax % Ngt
Ingcaciso of icompressor ulawulo indlela 0: Akukho compressor - iyunithi Condensing OFF I-1: Isantya esisisigxina - Igalelo le-DI1 elisetyenziselwa ukuqala / ukumisa i-compressor yesantya esisisigxina 2: Isantya esiguquguqukayo-Igalelo le-DI1 elisetyenziselwa ukuqala / ukumisa i-compressor elawulwa yisantya esiguqukayo kunye nomqondiso we-0 - 10 V kwi-AO2	c71	Imowudi yeComp
Ukulibazisa ixesha ngenxa phezulu ukukhupha igesi ubushushu (ngemizuzu) Xa i-sensor Td irekhoda ubushushu obuphezulu kunexabiso lomda elifakwe kwi-r84, i-timer iya kuqala. Xa ixesha lokulibaziseka liphelile, i-compressor iya kumiswa ukuba iqondo lokushisa lisephezulu kakhulu. I-alam nayo iya kukhutshwa.	c72	Disch. Del
Max. uxinzelelo (Ubukhulu. ukujiya uxinzelelo) Obona xinzelelo luphezulu luvumelekileyo lokujiya lubekwe apha. Ukuba uxinzelelo luyanda, i-compressor iya kumiswa.	c73	I-PCMax
Umahluko kubuninzi. Uxinzelelo (Uxinzelelo oluphantsi) Umahluko wokuqalisa kwakhona kwecompressor ukuba isikiwe ngenxa yePcMax. (Zonke izibali kufuneka ziphelelwe phambi kokuba ukuqalisa kwakhona kuvunyelwe)	c74	Ukwahlukana kwePC
Ubuncinane ukufunxa uxinzelelo Faka olona xinzelelo luphantsi luvumelekileyo lokufunxa apha. Icompressor imisiwe ukuba uxinzelelo lwehla ngaphantsi kwexabiso elincinci.	c75	PsLP
Ukufunxa uxinzelelo umahluko Umahluko wokuqalisa kwakhona kwecompressor ukuba inqunyulwe ngenxa ye-PSLP. (Zonke izibali kufuneka ziphelelwe phambi kokuba ukuqalisa kwakhona kuvunyelwe)	c76	PsDiff
Ampukungqinisisa into Kp ngenxa icompressor ummiselo Ukuba ixabiso le Kp lithotyiwe, ummiselo uzakucotha	c82	Cmp Kp
Ukudityaniswa ixesha Tn ngenxa icompressor ummiselo Ukuba ixabiso le-Tn linyusiwe, ummiselo uya kusebenza kakuhle	c83	Comp Tn umzuzwana
Ulwelo Isitofu Offset I-liquid injection relay iyasebenza xa iqondo lobushushu lingaphezulu kwe "r84" thabatha "c88" (kodwa kuphela ukuba icompressor iyasebenza).	c88	LI Offset
Ulwelo Isitofu i-hysterese I-liquid injection relay iye iyekiswe ukusebenza xa iqondo lobushushu lehlile laya kutsho ku-"r84" thabatha "c88" thabatha "c89".	c89	LI Hyst
Isicompressor Yeka ukulibazisa emva Ulwelo isitofu I-Compressor ON-ixesha emva kwe-relay "Aux relay" icinyiwe	c90	LI Ukulibazisa
Isantya esinqwenelekayo secompressor ngokunxulumene neempazamo zokuhambisa uxinzelelo. Isantya ngexesha lokusebenza ngokukhawuleza.	c93	CmpEmrgSpeed
Min Ngexesha ngexesha lobushushu obuphantsi kunye noxinzelelo oluphantsi	c94	c94 LpMinOnTime
IMeasured Tc apho isantya seComp min siphakanyiselwe kwi-StartSpeed	c95	c95 TcSpeedLim
I-LED engaphambili yomlawuli iya kubonisa ukuba ifriji iyaqhubeka.

Umlandeli		Umlandeli ulawulo
Ampukungqinisisa into Kp Ukuba ixabiso le-KP lithotyiwe, isantya sefeni siyakutshintsha.	n04	Kp factor
Ukudityaniswa Ixesha Tn Ukuba ixabiso le-Tn linyukile, isantya sefeni siya kutshintsha.	n05	Tn umzuzwana
Ampukungqinisisa into Kp max Ummiselo usebenzisa le Kp, xa ixabiso elilinganisiweyo likude kwireferensi	n95	Cmp kp Max
Umlandeli isantya Esona santya sabalandeli sifundwa apha njenge % yesantya segama.	F07	Isantya sefeni %
Guqula in fan isantya Utshintsho oluvunyelweyo kwisantya sefeni lungangenwa xa isantya sefeni siza kuthotywa. Useto lungangenwa njengepesentitagIxabiso le-e ngesekondi nganye.	F14	I-Downslope
Jog isantya Cwangcisa isantya sokuqalisa kwefeni apha. Emva kwemizuzwana elishumi umsebenzi wejog uya kumisa kwaye isantya se fan siya kulawulwa ngummiselo oqhelekileyo.	F15	Isantya seJog
Jog isantya at phantsi amaqondo obushushu Faka isantya sokubaleka esifunwayo kumaqondo obushushu angaphandle angama-20 °C nangaphantsi apha. (Kumaqondo obushushu angaphandle phakathi kwe +10 kunye ne -20, umlawuli uya kubala kwaye asebenzise isantya phakathi kwesetingi zejog ezimbini.)	F16	LowTempJog
Umlandeli ulawulo inkcazelo 0: Cishiwe I-1: I-fan ixhunywe kwi-terminal 5-6 kwaye isantya silawulwa yi-inter phase cut. I-relay kwi-terminal 15-16 idibanisa kwiimfuno zesantya se-95% okanye ngaphezulu. I-2: I-fan ixhunyiwe kwisixhobo sokulawula isantya sangaphandle. Isignali yokulawula isantya ixhunyiwe kwii-terminals 28-29. I-relay kwi-terminal 15-16 iya kudibanisa xa ummiselo kufuneka. (Ngexesha lolawulo lwangaphandle, useto F14, F15 kunye neF16 ziya kuhlala zisebenza)	F17	FanCtrlMode
Ubuncinane fan isantya Seta esona santya siphantsi sivumelekileyo sabalandeli apha. Ifeni iya kunqunyanyiswa ukuba umsebenzisi ungena ngesantya esisezantsi.	F18	MinFanSpeed
Ubuninzi fan isantya Isantya esiphezulu sefeni sinokukhawulwa apha. Ixabiso lingangenwa ngokucwangcisa isantya se-100% kwipesenti efunwayotage.	F19	MaxFanSpeed
Imanyuwali fan isantya ulawulo Ugqithiso lolawulo lwesantya sefeni lunokwenziwa apha. Lo msebenzi ufanelekile kuphela xa iswitshi ephambili ikwimo yenkonzo.	F20	Umlandeli Wesandla %
Imbuyekezo yesigaba Ixabiso linciphisa ingxolo yombane ekhutshwa ngexesha lolawulo lwesigaba. Ixabiso kufuneka litshintshwe kuphela ngabasebenzi abaqeqeshwe ngokukodwa.	F21	Fan Comp
Umtshini wecondenser uya kungenisa umoya we-compartment yecompressor ukuqinisekisa indawo ekhuselekileyo phambi kokuba icompressor iqale kwiifriji ezikhethiweyo ze-A2L nge-o30.	F23	Ixesha leFanVent
I-LED engaphambili yesilawuli iya kubonisa ukuba iFan iyaqhubeka ibonelelwa nokuba kungesantya solawulo lwesantya somlandeli okanye i-fan relay.

Okwenyani ixesha iwotshi
Xa usebenzisa unxibelelwano lwedatha iwotshi ilungiswa ngokuzenzekelayo yiyunithi yesistim. Ukuba umlawuli akanalo unxibelelwano lwedatha, iwotshi iya kuba nogcino lwamandla lweeyure ezine.		(Amaxesha akakwazi ukusetwa ngonxibelelwano lwedatha. Izicwangciso zifanelekile kuphela xa kungekho nxibelelwano lwedatha).
Tshintsha ukuya usuku ukusebenza Faka ixesha apho ireferensi yolawulo iba yindawo ebekiweyo engenisiweyo.	t17	Ukuqala kosuku
Guqula ukuya busuku ukusebenza Faka ixesha apho ireferensi yolawulo iphakanyiswa nge-r13.	t18	Ubusuku buqala
Ikloko: Ukumiselwa kweyure	t07
Ikloko: Useto lomzuzu	t08
Ikloko: Ukumiselwa komhla	t45
Ikloko: Ukumiselwa kwenyanga	t46
Ikloko: Ukumiselwa konyaka	t47
Iintlobo ngeentlobo		Iintlobo ngeentlobo
Ukuba umlawuli wakhiwe kwinethiwekhi ngonxibelelwano lwedatha, kufuneka abe nedilesi, kwaye iyunithi yenkqubo yonxibelelwano lwedatha kufuneka yazi ke le dilesi. Idilesi ibekwe phakathi kwe-0 kunye ne-240, kuxhomekeke kwiyunithi yesistim kunye nonxibelelwano lwedatha ekhethiweyo. Umsebenzi awusetyenziswanga xa unxibelelwano lwedatha iMODBUS. Ifunyanwa apha ngenkqubo yokuskena umsebenzi.
	o03
	o04

Ukufikelela ikhowudi 1 (Ukufikelela ukuya zonke iisetingi) Ukuba useto kumlawuli kufuneka ukhuselwe ngekhowudi yofikelelo ungamisela ixabiso lamanani phakathi kwe-0 kunye ne-100. Ukuba akunjalo, unokurhoxisa umsebenzi ngokucwangcisa u-0 (99 uya kuhlala ekunika ufikelelo).	o05	Acc. ikhowudi
Umlawuli isoftware inguqulelo	o08	SW ver
Khetha uphawu ngenxa i umboniso Apha uchaza uphawu oluza kuboniswa sisiboniso. I-1: Uxinzelelo lokufunxa kwiidigri, i-Ts. 2: Uxinzelelo loxinzelelo kwiidigri, Tc.	o17	Imo yokubonisa
Uxinzelelo umthumeli izicwangciso ngenxa Ps Uluhlu olusebenzayo lokuhambisa uxinzelelo - min. ixabiso	o20	MinTransPs
Uxinzelelo umthumeli izicwangciso ngenxa Ps Uluhlu olusebenzayo lokuhambisa uxinzelelo - max. ixabiso	o21	MaxTransPs
Isikhenkcisi ulungiselelo (kuphela ukuba “r12” = 0) Ngaphambi kokuba ifriji iqaliswe, ifriji kufuneka ichazwe. Unokukhetha phakathi kwezi friji zilandelayo 2=R22. 3=R134a. 13=Umsebenzisi uchaziwe. 17=R507. 19=R404A. 20=R407C. 21=R407A. 36=R513A. 37=R407F. 40=R448A. 41=R449A. 42=R452A. 39=R1234yf. 51=R454C. 52=R455A Isilumkiso: Ukukhethwa okungalunganga kwefriji kunokubangela umonakalo kwi-compressor. Ezinye iifriji: Apha ukubeka i-13 kukhethiwe kwaye emva koko izinto ezintathu -Ref.Fac a1, a2 kunye ne-a3 - nge-AKM kufuneka imiselwe.	o30	Isikhenkcisi
Idijithali igalelo uphawu - DI2 Umlawuli une-digital input 2 engasetyenziselwa omnye wale misebenzi ilandelayo: 0: Igalelo alisetyenziswa. Signal from a safety circuit (short-circuited =ok for compressor operation). Disconnected = compressor stop and A97 alarm). Main switch. Regulation is carried out when the input is short-circuited, and regulation is stopped when the input is put in pos. OFF. Ukusebenza ebusuku. Xa igalelo lifutshane, kuya kubakho umgaqo wokusebenza ebusuku. Umsebenzi we-alam owahlukileyo. I-alam iya kunikwa xa igalelo lifutshane. Umsebenzi we-alam owahlukileyo. I-alam iya kunikwa xa igalelo livuliwe. Input status, on or off (DI2 status can be tracked via data communication). 7: Alarm from the compressor’s external speed control.	o37	DI2 uqwalaselo.
Aux udluliselo umsebenzi 0: I-relay ayisetyenziswanga 1: Into yokufudumeza yangaphandle (ulungiselelo lobushushu kwi-r71, inkcazo yesivamvo ku-069) 2: Isetyenziselwa inaliti yolwelo (ukusetwa kobushushu kwi-r84) I-3: Umsebenzi wolawulo lokubuyisela i-oyile kufuneka usebenze i-relay	o40	AuxRelayCfg
Uxinzelelo umthumeli izicwangciso ngenxa PC Uluhlu olusebenzayo lokuhambisa uxinzelelo - min. ixabiso	o47	MinTransPc
Uxinzelelo umthumeli izicwangciso ngenxa PC Uluhlu olusebenzayo lokuhambisa uxinzelelo - max. ixabiso	o48	MaxTransPc
Khetha i uhlobo of ukujiya iyunithi. Iseti yefektri. Emva koseto lokuqala, ixabiso 'litshixiwe' kwaye lingatshintshwa kuphela xa umlawuli ephinde wamiselwa useto lwefektri. When entering the refrigerant setting, the controller will ensure that the ‘Unit type’ and refrigerant are compatible.	o61	Uhlobo lweyunithi
S3 Uqwalaselo 0 = igalelo le-S3 alisetyenziswanga I-1 = igalelo le-S3 elisetyenziselwa ukulinganisa ubushushu bokukhutshwa	o63	S3 uqwalaselo
Gcina as umzi-mveliso ulungiselelo Ngolu seto ugcina useto loqobo lomlawuli njengoseto olusisiseko esitsha (iisetingi zangaphambili zasefektri zibhalwa ngaphezulu).	o67	-

Chaza i sebenzisa of i Taux isivamvo (S5) 0: Ayisetyenziswa 1: Isetyenziselwa ukulinganisa ubushushu beoyile I-2: Isetyenziselwa ukulinganisa ubushushu bomsebenzi wokufudumala wangaphandle 3: Okunye ukusetyenziswa. Ukulinganisa ubushushu obukhethiweyo	o69	Taux Config
Ixesha ixesha ngenxa ukufudumeza isiqalelo in crankcase Ngeli xesha umlawuli uya kubala ngokwakhe ixesha lokuvala kunye ne-ON. Ixesha lingeniswa ngemizuzwana.	P45	Ixesha le-PWM
Umahluko ngenxa i ukufudumeza izinto 100% ON inqaku Umahluko usebenza kwinani ledigri ezingaphantsi kwe 'Tamb minus Ts = 0 K' ixabiso	P46	CCH_OnDiff
Umahluko ngenxa i ukufudumeza izinto izele CIMA inqaku Umahluko usebenza kwinani ledigri ngaphezulu kwe 'Tamb minus Ts = 0 K' ixabiso	P47	CCH_OffDiff

Ukusebenza ixesha ngenxa ukujiya iyunithi The condensing unit’s operating time can be read out here. The read-out value must be multiplied by 1,000 in order to obtain the correct value. (The displayed value can be adjusted if required)	P48	Ixesha lokuSebenza kweYunithi
Ukusebenza ixesha ngenxa i icompressor The compressors operating time can be read out here. The read-out value must be multi- plied by 1,000 in order to obtain the correct value. (The displayed value can be adjusted if required)	P49	Comp Runtime
Ukusebenza ixesha ngenxa ukufudumeza isiqalelo in crankcase Ixesha lokusebenza kwento yokufudumeza inokufundwa apha. Ixabiso lokufunda kufuneka liphindwe nge-1,000 ukwenzela ukufumana ixabiso elichanekileyo (ixabiso elibonisiweyo linokulungiswa xa lifunwa).	P50	CCH Ixesha lokuSebenza
Inani of HP iialam Inani lee-alam ze-HP linokufundwa apha (ixabiso elibonisiweyo linokulungiswa ukuba liyafuneka).	P51	HP Alarm Cnt
Inani of LP iialam Inani lee-alamu ze-LP linokufundwa apha (ixabiso elibonisiweyo linokulungiswa xa lifunwa).	P52	LP Alamu Cnt
Inani of ukukhupha iialam Inani lee-alam ze-Td linokufundwa apha (ixabiso elibonisiweyo linokulungiswa ukuba liyafuneka).	P53	I-DisAlarm Cnt
Inani of ivaliwe i-condenser iialam Inani lee-alam zecondenser ezivaliweyo zinokufundwa apha (ixabiso elibonisiweyo lingahlengahlengiswa ukuba liyafuneka).	P90	BlckAlrm Cnt
I-oyile ukubuya ulawulo Isantya umda Ukuba isantya secompressor sidlula lo mda, i-counter counter iya kwandiswa. Iya kuncitshiswa ukuba isantya secompressor siwela ngaphantsi kwalo mda.	P77	ORM SpeedLim
I-oyile ukubuya ulawulo ixesha Ixabiso eliqingqiweyo lekhawuntara yexesha elichazwe ngasentla. Ukuba i-counter idlula lo mda, isantya secompressor siya kuphakanyiswa kwisantya sokunyusa.	P78	Ixesha le-ORM
I-oyile ukubuya ulawulo Khuthaza isantya Esi santya secompressor siqinisekisa ukuba ioli ibuyela kwicompressor	P79	ORM BoostSpd
I-oyile ukubuya ulawulo Khuthaza ixesha. Ixesha lecompressor kufuneka isebenze kwi-Boost speed	P80	ORM BoostTim

Inkonzo		Inkonzo
Funda uxinzelelo lwePc	u01	Ibar yePC
Funda ubushushu beTaux	u03	T_aux
Ubume kwigalelo le-DI1. Ivuliwe/1=ivaliwe	u10	Ubume be-DI1
Imo yokusebenza ebusuku (ivuliwe okanye icinyiwe) kwi=ukusebenza kwasebusuku	u13	NightCond
Funda Ubushushu obugqithisileyo	u21	Ubushushu obukhulu SH
Funda ubushushu kwi-S6 sensor	u36	Ubushushu be-S6
Funda umthamo wecompressor kwi%	u52	CompCap %
Ubume kwigalelo le-DI2. Ivuliwe/1=ivaliwe	u37	Ubume be-DI2
Imo kwi-relay yecompressor	u58	Comp Relay
Imo kwi-relay yefeni	u59	Ugqithiso lwabalandeli
Imo kwi-relay ye-alam	u62	Ugqithiso lwe-alam
Imo kwi-relay "Aux"	u63	I-Aux Relay
Ubume kwi-relay yento yokufudumeza kwi-crankcase	u71	I-CCH Relay
Ubume kwigalelo le-DI3 (kwi/1 = 230 V)	u87	Ubume be-DI3
Funda ukuthoba uxinzelelo kwiqondo lobushushu	U22	Tc
Funda uxinzelelo INdu	U23	Ps
Funda uxinzelelo lokufunxa kwiqondo lobushushu	U24	Ts
Funda iqondo lobushushu elikhoyo kwindawo Tamb	U25	T_ambient
Funda ukukhutshwa kobushushu Td	U26	T_Discharge
Funda ubushushu berhasi efunxayo kwi-Ts	U27	T_Ukukhupha
Umqulutage kwimveliso ye-analogue AO1	U44	AO_1 Volt
Umqulutage kwimveliso ye-analogue AO2	U56	AO_2 Volt

Ukusebenza ubume		(Umlinganiselo)
Umlawuli uhamba kwiimeko ezithile zokulawula apho elinde nje inqaku elilandelayo lommiselo. Ukwenza ezi meko "kutheni kungekho nto eyenzekayo" ibonakala, unokubona isimo sokusebenza kwisiboniso. Cofa ngokufutshane (1s) iqhosha eliphezulu. Ukuba kukho ikhowudi yesimo, iya kuboniswa kwisibonisi. Iikhowudi zesimo ngasinye zineentsingiselo ezilandelayo:		Ctrl. chaza:
Ummiselo oqhelekileyo	S0	0
Xa isicompressor sisebenza kufuneka sisebenze ubuncinane x imizuzu.	S2	2
Xa icompressor imisiwe, kufuneka ihlale imisiwe kangangemizuzu x ubuncinane.	S3	3
Isikhenkcezisi simiswe ngokutshintsha okungundoqo. Nokuba nge-r12 okanye nge-DI-input	S10	10
Ukulawulwa kweziphumo ngezandla	S25	25
Akukho friji ekhethiweyo	S26	26
Ukhuseleko olusikiweyo Max. uxinzelelo lokujiya lugqithile. Zonke iicompressor zayeka.	S34	34
Okunye ibonisa:
Igama lokugqithisa liyafuneka. Seta igama lokugqithisa	PS
Ummiselo unqunyanyiswe ngokutshintsha okungundoqo	CIMA
Akukho friji ekhethiweyo	Ref
Akukho didi lukhethiweyo lweyunithi yokunciphisa.	uchwethezo

Impazamo umyalezo
Kwimeko yempazamo ii-LED ezingaphambili ziya kudanya kwaye i-alarm relay iya kuvula. Ukuba ucofa iqhosha eliphezulu kule meko ungabona ingxelo ye-alamu kwisibonisi. Kukho iintlobo ezimbini zeengxelo zempazamo - inokuba yi-alam eyenzeka ngexesha lokusebenza kwemihla ngemihla, okanye kunokubakho isiphene kufakelo. Ii-alam aziyi kubonakala kude kuphele ukulibaziseka kwexesha elimisiweyo. Ii-alarm ze-E, kwelinye icala, ziya kubonakala xa kusenzeka impazamo. (I-alam ayizukubonakala okoko nje kukho i-alam ye-E esebenzayo). Nantsi imiyalezo enokuthi ivele:
Ikhowudi / Ialarm umbhalo ngokusebenzisa idatha unxibelelwano	Inkcazo	Isenzo
I-A2/— i-alamu ye-LP	Uxinzelelo lokufunxa oluphantsi	Jonga imiyalelo yeyunithi yokudibanisa
A11/— Akukho Rfg. sel.	Akukho friji ekhethiweyo	Seta o30
A16 /— DI2 alarm	DI2 ialam	Jonga umsebenzi othumela umqondiso kwigalelo le-DI2
I-A17 / —I-Alam ye-HP	I-Alarm ye-C73 / DI3 (i-alamu yoxinzelelo oluphezulu / oluphantsi)	Jonga imiyalelo yeyunithi yokudibanisa
A45 /— Imo yokulinda	Indawo yokulinda (ifriji emisiweyo nge-r12 okanye i-DI1-input)	I-r12 kunye/okanye igalelo le-DI1 liya kuqalisa ummiselo
A80 / — Cond. ivaliwe	Ukuhamba komoya kwehlile.	Coca iyunithi yokudibanisa
A96 / — Max Disc. Temp	Ubushushu bokukhutshwa kwerhasi bugqithile	Jonga imiyalelo yeyunithi yokudibanisa
I-A97 / - I-alamu yokhuseleko	Umsebenzi wokhuseleko kwi-DI2 okanye i-DI 3 iyasebenza	Khangela umsebenzi othumela isignali kwi-DI2 okanye i-DI3 igalelo kunye nolwalathiso lokujikeleza kwe-compressor
A98 / — Qhuba ialam	I-alam evela kummiselo wesantya	Jonga ummiselo wesantya
E1 /— Ctrl. Impazamo	Iimpazamo kwisilawuli	Jonga inzwa kunye noqhagamshelo
E20 /— Impazamo yoluvo lwePc	Imposiso kwisidlulisi soxinzelelo lwePc
E30 /— Taux Sensor Err	Impazamo kwi-Aux sensor, S5
E31/—Impazamo yoVavanyo lweTamb	Impazamo kwinzwa yomoya, S2
E32 / —Impazamo yeSensor yeTdis	Imposiso kwinzwa yokukhupha, S3
I-E33 / —Impazamo yoVavanyo lweTsuc	Impazamo kwinzwa yerhasi yokufunxa, i-S4
E39/— Ps Isivamvo Impazamo	Impazamo kwisidlulisi soxinzelelo Ps
Idatha unxibelelwano Ukubaluleka kwee-alamu zomntu ngamnye kunokuchazwa ngokucwangcisa. Ukuseta kufuneka kwenziwe kwiqela "Iindawo zeAlarm" Settings from System manager Settings from AKM (AKM destination) Ngena Ugqithiso lwe-alam Thumela ngeNethiwekhi Hayi Phezulu Phantsi-Phakamileyo Phezulu 1 X X X X Phakathi 2 X X X Phantsi 3 X X X Ngena kuphela X Kukhubazekile

Ukusebenza

Bonisa
Amaxabiso aya kuboniswa enamanani amathathu, kwaye kunye nocwangciso unokugqiba ukuba ubushushu buboniswe kwi °C okanye kwi °F.

Iidiode ezikhupha ukukhanya (i-LED) kwiphaneli engaphambili
Ii-LED kwiphaneli yangaphambili ziya kukhanya xa i-relay efanelekileyo ivuliwe.

• = Isikhenkcisi
• = into yokufudumeza kwikhrankcase ivuliwe
• = Ukubaleka kwefeni
  • Iidiode ezikhupha ukukhanya ziya kudanyaza xa kukho i-alam.
  • Kule meko unokukhuphela ikhowudi yempazamo kwisiboniso kwaye urhoxise/usayine i-alam ngokunika iqhosha elingasentla ukutyhala ngokufutshane.

Amaqhosha
When you want to change a setting, the upper and the lower button will give you a higher or lower value depending on the button you are pushing. But before you change the value, you must have access to the menu. You obtain this by pushing the upper button for a couple of seconds – you will then enter the column with parameter codes. Find the parameter code you want to change and push the middle buttons until value for the parameter is shown. When you have changed the value, save the new value by once more pushing the middle button. (If not operated for 20 (5) seconds, the display will change back to the Ts/Tc temperature display).

ExampLes

Seta imenyu

1. Cofa iqhosha eliphezulu de kuboniswe iparamitha r05
2. Cofa iqhosha eliphezulu okanye elisezantsi kwaye ufumane iparameter ofuna ukuyitshintsha
3. Cofa iqhosha eliphakathi de ixabiso leparameter libonisiwe
4. Cofa iqhosha eliphezulu okanye elisezantsi kwaye ukhethe ixabiso elitsha
5. Cinezela iqhosha eliphakathi kwakhona ukumisa ixabiso.

I-alam ye-Cutout yesilayidi / i-alam yerisithi/bona ikhowudi ye-alam

• Ukucofa okufutshane kwiqhosha eliphezulu
• Ukuba kukho iikhowudi ezininzi ze-alam zifumaneka kwi-rolling stack. Cofa elona qhosha liphezulu okanye lisezantsi ukuskena istaki esiqengqelekayo.

Beka Indawo

1. Cofa iqhosha eliphakathi de ixabiso lobushushu libonisiwe
2. Cofa iqhosha eliphezulu okanye elisezantsi kwaye ukhethe ixabiso elitsha
3. Cofa iqhosha eliphakathi kwakhona ukuqukumbela isicwangciso.

• Ukufunda iqondo lobushushu kwi-Ts (ukuba i-Tc sisiboniso sokuqala) okanye i-Tc (ukuba i-Ts luphawu oluphambili)
• Ukucofa okufutshane kweqhosha elisezantsi

Qalisa kakuhle
Ngenkqubo elandelayo unokuqalisa ummiselo ngokukhawuleza okukhulu:

1. Vula iparameter r12 kwaye umise ummiselo (kwiyunithi entsha kwaye engamiselwanga ngaphambili, i-r12 iya kube sele isetelwe ku-0 oku kuthetha ukuba umiselo olumisiweyo.
2. Khetha ifriji ngeparameter o30
3. Vula iparameter r12 kwaye uqale ummiselo. Qala/yima kwigalelo le-DI1 okanye i-DI2 nayo kufuneka ivulwe.
4. Yiya kwisaveyi yezicwangciso zasefektri. Yenza naluphi na utshintsho oluyimfuneko kwiiparamitha ezifanelekileyo.
5. Yenethiwekhi.
   • Seta idilesi ku-o03
   • Vula umsebenzi wokuskena kumphathi wenkqubo.

Phawula

• Xa uhambisa iyunithi yokunciphisa, umlawuli uya kusekwa kuhlobo lweyunithi yokunciphisa (ukusetha o61). Olu seto luzakuthelekiswa nesetingi yefriji yakho. Ukuba ukhetha "ifriji engavumelekanga", isiboniso siya kubonisa "ref" kwaye silindele isethingi esitsha.
• (Xa kukho utshintsho lomlawuli, i-061 kufuneka ibekwe njengoko kubonisiwe kwimiyalelo evela kuDanfoss)

Uphando lwemenyu

Ipharamitha			Min. ixabiso	Max. ixabiso	Umzi-mveliso ulungiselelo	Okwenyani ulungiselelo
Umsebenzi		Ikhowudi
Okuqhelekileyo ukusebenza
Seta indawo (ireferensi yommiselo ilandela inani leedigri ngaphezu kobushushu obungaphandle kweTamb)		---	2.0 K	20.0 K	8.0 K
Ummiselo
Khetha i-SI okanye idispleyi yase-US. 0=SI (ibha kunye no °C). 1=US (Psig kunye °F)		R05	0/°C	1/F	0/°C
Utshintsho olungundoqo lwangaphakathi. Incwadi kunye nenkonzo = -1, Misa ummiselo = 0, Qala ummiselo =1		R12	-1	1	0
I-offset ngexesha lokusebenza ebusuku. Ngexesha lokusebenza ebusuku ireferensi iphakanyiswe ngeli xabiso		R13	0 K	10 K	2 K
Seta indawo yoxinzelelo lokufunxa i-Ts (kuphela kwi-Optyma™ Ukongeza kwi-inverter)		R23	-30 °C	10 °C	-7 °C
Ukufundwa kwereferensi ye-Tc		R29				-
Ixabiso lokusikwa kweThermostat yesixhobo sokufudumeza sangaphandle (069=2 kunye ne-o40=1)		R71	-30,0 °C	30,0 °C	-25 °C
Min. iqondo lobushushu elijiyisayo (elona salathisi se-Tc esivumelekileyo)		R82	0 °C	40 °C	25 °C
Max. iqondo lobushushu elijiyisayo (elona salathisi se-Tc esiphezulu esivunyelweyo)		R83	20 °C	50 °C	40 °C
Max. ukukhutshwa kweqondo lokushisa kwegesi Td		R84	50 °C	140 °C	125 °C
Iialamu
Ukulibaziseka kwexesha le-alam kwisiginali kwigalelo le-DI2. Isebenza kuphela ukuba o37=4 okanye 5.		A28	0 imiz.	240 imiz.	30 imiz.
Ialam yokungapholi ngokwaneleyo kwicondenser. Umahluko wobushushu 30.0 K = I-Alarm ivaliwe		A70	3.0 K	30.0 K	10.0 K
Libazise ixesha le-alam ye-A80. Jonga kwakhona ipharamitha A70.		A71	5 imiz.	240 imiz.	30 imiz.
Isicompressor
Min. Ngexesha		c01	1 s	240 s	5 s
Min. OFF-ixesha		c02	3 s	240 s	120 s
Min. ixesha phakathi kwecompressor iqala		c07	0 imiz.	30 imiz.	5 imiz.
Umda wokumpompa phantsi apho icompressor imisiwe (ukusetha i-0.0 = akukho msebenzi)	***	c33	0,0 ibha	6,0 ibha	0,0 ibha
Min. isantya compressor		c46	25 Hz	70 Hz	30 Hz
Isantya sokuqala secompressor		c47	30 Hz	70 Hz	50 Hz
Max. isantya compressor		c48	50 Hz	100 Hz	100 Hz
Max. isantya secompressor ngexesha lokusebenza ebusuku (%-value of c48)		c69	50%	100%	70%
Inkcazo yemodi yokulawula i-compressor 0: Akukho compressor - Iyunithi yokunciphisa i-OFF I-1: Isantya esisisigxina - Igalelo le-DI1 elisetyenziselwa ukuqala / ukumisa i-compressor yesantya esisisigxina 2: Isantya esiguquguqukayo-Igalelo le-DI1 elisetyenziselwa ukuqala / ukumisa i-compressor elawulwa yisantya esiguqukayo kunye nomqondiso we-0 - 10 V kwi-AO2	*	c71	0	2	1
Ukulibaziseka kwexesha kwi-Td ephezulu. Icompressor iya kuyeka xa ixesha liphelile.		c72	0 imiz.	20 imiz.	1 imiz.
Max. uxinzelelo. I-Compressor iyayeka ukuba uxinzelelo oluphezulu lurekhodwa	***	c73	7,0 ibha	31,0 ibha	23,0 ibha
Umahluko kubuninzi. uxinzelelo (c73)		c74	1,0 ibha	10,0 ibha	3,0 ibha
Min. uxinzelelo lokufunxa INdu. I-Compressor iyayeka ukuba uxinzelelo oluphantsi lurekhodwa	***	c75	-0,3 ibha	6,0 ibha	1,4 ibha
Umahluko kwi min. uxinzelelo lokufunxa kunye nokumpompa phantsi		c76	0,1 ibha	5,0 ibha	0,7 ibha
Ampliification factor Kp for compressors PI-regulation		c82	3,0	30,0	20,0
Ixesha lokuhlanganisa Tn for compressors PI-umgaqo		c83	30 s	360 s	60 s
I-Liquid Injection Offset		c88	0,1 K	20,0 K	5,0 K
Ulwelo Isitofu hysterese		c89	3,0 K	30,0 K	15,0 K
Ukulibaziseka kokumisa iCompressor emva kokutofa ulwelo		c90	0 s	10 s	3 s
Isantya secompressor esinqwenelekayo ukuba umqondiso ovela kwi-Ps yokuhambisa uxinzelelo uyasilela		c93	25 Hz	70 Hz	60 Hz
Min Ngexesha ngexesha le-Low Ambient LP		c94	0 s	120 s	0 s
Measured Tc for which the Comp min speed is raised to Start Speed		c95	10,0 °C	70,0 °C	50,0 °C
Ulawulo iiparamitha
Ampi-liification factor Kp yolawulo lwe-PI		n04	1.0	20.0	7.0
Ixesha lokudibanisa Tn ye-PI-ummiselo		n05	20	120	40
Kp max kulawulo lwePI xa umlinganiselo ukude kwireferensi		n95	5,0	50,0	20,0
Umlandeli
Ukufundwa kwesantya sabalandeli kwi%		F07	-	-	-
Imvume yotshintsho kwisantya sefeni (kwixabiso eliphantsi) % ngomzuzwana.		F14	1,0%	5,0%	5,0%
Isantya sokubaleka (isantya njenge % xa ifeni iqaliswa)		F15	40%	100%	40%

waqhubeka

Ikhowudi

Min.

Max.

Ubuso

Okwenyani

Isantya seJog kubushushu obuphantsi		F16	0%	40%	10%
Definition of fan control: 0=Off; Internal control (AC Fan); External speed control (EC Fan)		F17	0	2	1
Ubuncinci besantya sabalandeli. Ukuncipha kwesidingo kuya kumisa i-fan.		F18	0%	40%	10%
Isantya esiphezulu somqhubi		F19	40%	100%	100%
Ulawulo lwezandla lwesantya somlandeli. (Kuxa i-r12 imiselwe ku--1)	**	F20	0%	100%	0%
Imbuyekezo yesigaba (kufuneka itshintshwe kuphela ngabasebenzi abaqeqeshwe ngokukodwa.)		F21	0	50	20
Ixesha langaphambi kokuPhumeza umoya kwiifriji ze-A2L ngaphambi kokuba icompressor iqale		F23	30	180	30
Okwenyani ixesha iwotshi
Ixesha abatshintshela ngalo kumsebenzi wosuku		t17	0 iiyure	23 iiyure	0
Ixesha apho batshintshela ekusebenzeni ebusuku		t18	0 iiyure	23 iiyure	0
Iwotshi – Ukusetwa kweeyure		t07	0 iiyure	23 iiyure	0
Iwotshi – Ukusetwa komzuzu		t08	0 imiz.	59 imiz.	0
Iwotshi – Ukusetwa komhla		t45	usuku olu-1	Iintsuku ezi-31	1
Ikloko – Ukusetwa kwenyanga		t46	1 mon.	12 mon.	1
Ikloko-Umiselo lonyaka		t47	0 unyaka	iminyaka eyi-99	0
Iintlobo ngeentlobo
Idilesi yenethiwekhi		o03	0	240	0
Vula/Vala iswitsha (Umyalezo wePin yeNkonzo) KUBALULEKILE! o61 kufuneka ibekwe phambi kwe-o04 (isetyenziswe e-LON 485 kuphela)		o04	0/Cima	1/Ngokwexesha	0/Cima
Ikhowudi yofikelelo (ufikelelo kuzo zonke iisetingi)		o05	0	100	0
Ukufundwa koguqulelo lwesoftware yabalawuli		o08
Khetha isignali yokubonisa view. 1=Uxinzelelo lokufunxa ngezidanga, Ts. 2=Uxinzelelo loxinzelelo ngokwezidanga, Ts		o17	1	2	1
Uluhlu olusebenzayo lwesidlulisi soxinzelelo Ps - min. ixabiso		o20	-1 ibha	5 ibha	-1
Uluhlu olusebenzayo lwesidlulisi soxinzelelo Ps- max. ixabiso		o21	6 ibha	200 ibha	12
Ulungiselelo lwesikhenkcisi: 2=R22. 3=R134a. 13=Umsebenzisi uchaziwe. 17=R507. 19=R404A. 20=R407C. 21=R407A. 36=R513A. 37=R407F. 40=R448A. 41=R449A. 42=R452A. 39=R1234yf. 51=R454C. 52=R455A	*	o30	0	42	0
Isiginali yongeniso kwi-DI2. Umsebenzi: (0=ayisetyenziswanga, 1=Umsebenzi wokhuseleko wangaphandle. Lawula xa ivaliwe, 2=isitshixo esingundoqo sangaphandle, 3=Umsebenzi wasebusuku xa uvaliwe, 4=umsebenzi we-alam xa uvaliwe, 5=i-alam xa ivuliwe. 6=i-alam esweni 7=I-alam evela kummiselo wesantya		o37	0	7	0
Umsebenzi we-Aux relay: (0=ayisetyenziswanga, 1=Into yokufudumeza yangaphandle, 2=inaliti elulwelo, 3=umsebenzi wokubuyisela i-oyile)	***	o40	0	3	1
Uluhlu olusebenzayo lwesidlulisi soxinzelelo lwePc – min. ixabiso		o47	-1 ibha	5 ibha	0 ibha
Uluhlu olusebenzayo lwesidlulisi soxinzelelo lwePc – max. ixabiso		o48	6 ibha	200 ibha	32 ibha
Ukusetwa kohlobo lweyunithi yoxinaniso (lusetwa lwasefektri xa umlawuli enyusiwe kwaye akanakuguqulwa emva koko)	*	o61	0	77	0
Igalelo loluvo S3 lizakusetyenziswa ukulinganisa ubushushu berhasi yokukhupha (1=ewe)		o63	0	1	1
Buyisela useto lwefektri yesilawuli ngoseto lwangoku		o67	Valiwe (0)	Ngo (1)	Valiwe (0)
Ichaza usetyenziso lwesivamvo se-Taux: 0=engasetyenziswanga; 1=umlinganiselo wobushushu be-oyile; 2=umlinganiselo osuka kumsebenzi wobushushu wangaphandle 3=olunye usetyenziso olunokuzikhethela		o69	0	3	0
Ixesha lexesha lokufudumeza into kwikhrankcase (KUVULA + OFF)		P45	30 s	255 s	240 s
Umahluko kwizinto zokufudumeza 100% ON point		P46	-20 K	-5 K	-10 K
Umahluko kwizinto zokufudumeza 100% OFF indawo		P47	5 K	20 K	10 K
Ukufundwa kwexesha lokusebenza kwiyunithi yecondenser. (Ixabiso maliphindaphindwe nge-1,000). Ixabiso lingalungiswa.		P48	-	-	0 h
Ukufundwa kwexesha lokusebenza kwecompressor. (Ixabiso maliphindaphindwe nge-1,000). Ixabiso lingalungiswa.		P49	-	-	0 h
Ukufundwa kwexesha lokusebenza kwento yokufudumeza kwi-crankcase. (Ixabiso maliphindaphindwe nge-1,000). Ixabiso lingalungiswa.		P50	-	-	0 h
Ukufundwa-ngaphandle kwenani le-alam ze-HP. Ixabiso lingalungiswa.		P51	-	-	0
Ukufundwa-ngaphandle kwenani le-alam ze-LP. Ixabiso lingalungiswa.		P52	-	-	0
Ukufundwa-ngaphandle kwenani lee-alam ze-Td. Ixabiso lingalungiswa.		P53	-	-	0
Ukufundwa-ngaphandle kwenani lee-alam zecondenser ezivaliweyo. Ixabiso lingalungiswa		P90	-	-	0
Ulawulo lokubuyisela i-oyile. Isantya seCompressor sendawo yokuqalisa ikhawuntara		P77	25 Hz	70 Hz	40 Hz

waqhubeka

Ikhowudi

Min.

Max.

Ubuso

Okwenyani

Ulawulo lokubuyisela i-oyile. Umlinganiselo wexabiso lekhawuntari		P78	5 imiz.	720 imiz.	20 imiz.
Ulawulo lokubuyisela i-oyile. Ukunyusa-isantya		P79	40 Hz	100 Hz	50 Hz
Ulawulo lokubuyisela i-oyile. Ixesha lokunyusa.		P80	10 s	600 s	60 s
Inkonzo
Uxinzelelo lokufunda kwiPc		u01	ibha
Readout lobushushu Taux		u03	°C
Ubume kwigalelo le-DI1. 1=ivuliwe=ivaliwe		u10
Imo yokusebenza ebusuku (ivuliwe okanye icinyiwe) 1=on=umsebenzi wasebusuku		u13
Readout superheat		u21	K
Ubushushu bokufunda kwi-S6 sensor		u36	°C
Ubume kwigalelo le-DI2. 1=ivuliwe=ivaliwe		u37
Funda umthamo wecompressor kwi%		u52	%
Ubume kwi-relay ukuya kwicompressor. 1=ivuliwe=ivaliwe	**	u58
Imo ekugqithiseni kwifeni. 1=ivuliwe=ivaliwe	**	u59
Imo kwi-relay ukuya kwi-alam. 1=ivuliwe=ivaliwe	**	u62
Imo kwi-relay "Aux". 1=ivuliwe=ivaliwe	**	u63
Ubume bokudluliselwa kwezinto zokufudumeza kwi-crank case. 1=ivuliwe=ivaliwe	**	u71
Ubume kumthamo ophezulutage igalelo DI3. 1=on=230 V		u87
Uxinzelelo lokunyuswa kokufunda kwiqondo lobushushu		U22	°C
Uxinzelelo lokufunda INdu		U23	ibha
Uxinzelelo lokufunxa olufundiweyo kwiqondo lobushushu		U24	°C
Readout iqondo lobushushu elikhoyo kwi Tamb		U25	°C
Ubushushu bokukhutshwa kokufunda Td		U26	°C
Readout ubushushu berhasi yokufunxa Ts		U27	°C
Funda umqulutage kwimveliso AO1		U44	V
Funda umqulutage kwimveliso AO2		U56	V

• *) Inokumiselwa kuphela xa ummiselo umisiwe (r12=0)
• **) Inokulawulwa ngesandla, kodwa kuphela xa r12=-1
• ***) Le parameter ixhomekeke kwiparameter o30 kunye neo61 izicwangciso

Ulungiselelo lwasefektri
Ukuba ufuna ukubuyela kumaxabiso aseti yefektri, inokwenziwa ngolu hlobo:

• Sika umthamo wonikezelotage kumlawuli
• Gcina iqhosha eliphezulu nelisezantsi licinezelekile ngaxeshanye njengoko uphinda uqhagamshela umthamo wonikezelotage

Ukuseta kwakhona iiparamitha zezibalo zeyunithi
Zonke iiparamitha zobume beYunithi (P48 ukuya kwi-P53 kunye ne-P90) zinokusetwa / zicocwe kusetyenziswa le nkqubo ilandelayo.

• Cwangcisa uTshintsho oluphambili ukuya ku-0
• Guqula iiparamitha zeNkcazo-manani - njengokuseta izixhobo zokubala ze-alam zibe ngu-0
• Lindela imizuzwana eyi-10 - ukuqinisekisa ukuba ubhalele kwi-EEROM
• Yenza amandla kwakhona kuMlawuli - tshintshela useto olutsha "kumsebenzi wezibalo"
• Cwangcisa i-Main Switch ON - kwaye iiparameters zisetelwe kwixabiso elitsha

Uqhagamshelwano

• DI1
  Isiginali yengeniso yedijithali.
  Isetyenziselwa ukuqalisa/ukuyeka ukupholisa (i-thermostat yegumbi)
  Iqala xa igalelo lifutshane.
• DI2
  Isiginali yengeniso yedijithali.
  Umsebenzi ochaziweyo uyasebenza xa igalelo lifutshane/livuliwe. Umsebenzi uchazwe kwi-o37.
• Pc
  Umshicileli woxinzelelo, i-ratiometric AKS 32R, i-0 ukuya kwi-32 bar
  Qhagamshela kwitheminali 28, 29 kunye ne30.
• Ps
  Isidluliseli soxinzelelo, iratiometric umz. AKS 32R, -1 ukuya kwibha ye-12 Idityaniswe kwitheminali 31, 32 kunye ne-33.
• S2
  Isivamvo somoya, iTamb. Pt 1000 ohm isivamvo, umz. I-AKS 11
• S3
  Ukukhupha inzwa yegesi, Td. Pt 1000 ohm isivamvo, umz. AKS 21
• S4
  Ubushushu berhasi yokufunxa, Ts. Pt 1000 ohm isivamvo, umz. I-AKS 11
• S5,
  Umlinganiselo wobushushu owongezelelweyo, Taux. Pt 1000 ohm isivamvo, umz. I-AKS 11
• S6,
  Umlinganiselo wobushushu owongezelelweyo, S6. Pt 1000 ohm isivamvo, umz. I-AKS 11
• EKA Bonisa
  Ukuba kukho ukufunda kwangaphandle / ukusebenza komlawuli, uhlobo lokubonisa i-EKA 163B okanye i-EKA 164B inokudityaniswa.
• RS485 (iterminal 51, 52,53)
  Kunxibelelwano lwedatha, kodwa kuphela ukuba imodyuli yonxibelelwano lwedatha ifakwe kumlawuli. Imodyuli ingaba yiLon.
  Ukuba unxibelelwano lwedatha lusetyenziswa, kubalulekile ukuba ukufakwa kwekhebula lonxibelelwano lwedatha lwenziwe ngokuchanekileyo.
  Jonga uncwadi olwahlukileyo Nomb. RC8AC...
• I-AO1, i-terminal 54, 55
  Isiginali yesiphumo, 0 – 10 V. Kufuneka isetyenziswe ukuba ifeni ixhotyiswe ngesantya sangaphakathi solawulo kunye ne-0 – 10 V DC igalelo, umz. EC-motor.
• I-AO2, i-terminal 56, 57
  Umqondiso wesiphumo, 0 - 10 V. Kufuneka isetyenziswe ukuba i-compressor ilawulwa ngesantya.
• MODBUS (iterminal 60, 61, 62)
  Yakhelwe kunxibelelwano lwedatha ye-Modbus.
  If data communication is used, it is important that the installation of the data communication cable is performed correctly. See separate literature No. RC8AC… (Alternatively the terminals can be connected to an external display type EKA 163A or 164A, but then they cannot be used for data communication. Any data communication must then be carried out by one of the other methods.)
• Ukubonelela ngevoltage
  I-230 V AC (Oku kufuneka kube sisigaba esifanayo kuzo zonke ii-230 V zoqhagamshelo).
• FAN
  Uqhagamshelwano lwabalandeli. Isantya silawulwa ngaphakathi.
• Ialarm
  Kukho uxhulumaniso phakathi kwe-terminal 7 kunye ne-8 kwiimeko ze-alamu kwaye xa umlawuli engenamandla.
• Comp
  Isicompressor. Kukho unxibelelwano phakathi kwe-terminal 10 kunye ne-11, xa icompressor isebenza.
• I-CCH
  Ukufudumeza into kwikhrankcase
  Kukho uxhumano phakathi kwee-terminals 12 kunye ne-14 xa ukufudumala kwenzeka.
• Umlandeli
  Kukho unxibelelwano phakathi kweetheminali ze-15 kunye ne-16 xa isantya somqhubi siphakanyiswe ngaphezu kwe-95%. (Isiginali yefeni iyatshintsha ukusuka kwi-terminal 5-6 ukuya kwi-15-16. Qhagamshela ucingo olusuka kwi-terminal 16 ukuya kwifeni.)
• Aux
  Inaliti yolwelo kumgca wokufunxa / into yokufudumeza yangaphandle / umsebenzi wokubuyisela ioyile kwicompressor elawulwa ngesantya
  Kukho unxibelelwano phakathi kwee-terminals 17 kunye ne-19, xa umsebenzi usebenza.
• DI3
  Isiginali yokufaka idijithali ukusuka esweni eliphantsi / eliphezulu loxinzelelo.
  Umqondiso kufuneka ube nomthamotage ye 0 / 230 V AC.
• Ingxolo yombane
  Iintambo zabenzi boluvo, amagalelo e-DI kunye nonxibelelwano lwedatha kufuneka zigcinwe zahlukile kwezinye iintambo zombane:
  • Sebenzisa iitreyi zentambo ezahlukeneyo
  • Gcina umgama phakathi kweentambo ubuncinci be-10 cm.
  • Iintambo ezinde kwigalelo le-DI kufuneka ziphetshwe

Iingqwalasela zofakelo

• Umonakalo owenziwe ngengozi, ufakelo olulambathayo, okanye iimeko zesiza, zinokubangela ukungasebenzi kakuhle kwenkqubo yolawulo, kwaye ekugqibeleni kukhokelele ekonakaleni kwesityalo. Lonke ukhuseleko olunokwenzeka lufakwe kwiimveliso zethu ukunqanda oku. Nangona kunjalo, ukufakela okungalunganga, umzekeloample, isenokubangela iingxaki. Ulawulo lwe-elektroniki alunakuthatha indawo yesiqhelo, ubunjineli obulungileyo.
• I-Danfoss ayiyi kuba noxanduva lwazo naziphi na iimpahla, okanye i-compo-nents yezityalo, ezonakalisiweyo ngenxa yeziphene ezingentla. Luxanduva lomfakeli ukujonga ukufakela ngokucokisekileyo, kunye nokufanela izixhobo eziyimfuneko zokhuseleko. Isalathiso esikhethekileyo senziwe kwimfuno-ubungakanani beempawu kumlawuli xa i-compressor imisiwe kunye nesidingo sabamkeli bamanzi phambi kwee-compressors.
• I-arhente ye-Danfoss yendawo yakho iya kuvuya ukukunceda ngeengcebiso ezingaphezulu, njl.

Idatha

Ukubonelela ngevoltage	230 V AC +10/-15%. 5 VA, 50 / 60 Hz
Isivamvo S2, S3, S4, S5, S6	Pt 1000
Ukuchaneka	Uluhlu lokulinganisa	-60 - 120 °C (S3 ukuya ku-150 °C)
	Umlawuli	±1 K below -35°C± 0.5 K between -35 – 25 °C;±1 K above 25 °C
	Pt 1000 inzwa	±0.3 K at 0 °C±0.005 K per degree
Umlinganiselo wePc, INdu	Umdlulisi woxinzelelo	Ratiometric. umz. AKS 32R, DST-P110
Bonisa	I-LED, i-3-digits
Umboniso wangaphandle	EKA 163B okanye 164B (nayiphi na i-EKA 163A okanye 164A)
Amagalelo edijithali DI1, DI2	Signal from contact functions Requirements to contacts: Gold plating Cable length must be max. 15 mUse auxiliary relays when the cable is longer
Igalelo ledijithali DI3	I-230 V AC evela kwi-pressostat yokhuseleko. Uxinzelelo oluphantsi / oluphezulu
Intambo yoqhagamshelo lombane	Ubuninzi.1.5 mm2 multi-core cable
Isiphumo seTriac	Umlandeli	Max. 240 V AC, Min. 28 V AC Max. 2.0 ALeak < 1 mA
iiRelay*		CE (250 V AC)
	Comp, CCH	4 (3) A
	Ialam, iFan, iAux	4 (3) A
Imveliso ye-analog	iipcs ezi-2. 0 - 10 V DC (Kulawulo lwangaphandle lwesantya sabalandeli kunye neecompressors) Min. umthwalo = 10 K ohm. (Ubukhulu 1mA)
Ubume bendalo	-25 – 55 °C, Ngexesha lokusebenza -40 – 70 °C, Ngexesha lothutho
	20 – 80% iRh, ayicondensed
	Akukho mpembelelo yokothuka / iintshukumo
Ukuxinana	IP20
Ukunyuka	DIN-kaloliwe okanye udonga
Ubunzima	0.4 kg
Unxibelelwano ngedatha	Ilungisiwe		IMODBUS
	Iinketho zokwandisa		I-LON
Ugcino lwamandla ewotshi	iiyure ezi-4
Iimvume	EC Umthamo ophantsitage Umyalelo kunye ne-EMC ifuna ukuba ukumakishwa kwe-CE kuthotyelwe I-LVD ivavanywe i-acc. I-EN 60730-1 kunye ne-EN 60730-2-9, A1, A2 EMC-ivavanywe acc. I-EN 61000-6-2 kunye ne-EN 61000-6-3

Ukuodola

Danfoss AIS

• Izisombululo zeMozulu
• danfoss.com
• +45 7488 2222

Any information, including, but not limited to information on selection of product, its application or use, product design, weight, dimensions, capacity or any other technical data in product manuals, catalogues descriptions, advertisements, etc. and whether made available in writing, orally, electronically, online or Via download, shall be considered informative, and is only binding if and to the extent, explicit reference is made in a quotation or order confirmation. Danfoss cannot accept any responsibility for possible errors in catalogues, brochures, videos and other material. Danfoss reserves the right to alter its products without notice. This also applies to products ordered but not delivered provided that such alterations can be made without changes to form, fit or function of the product. All trademarks in this material are property of Danfoss A/S or Danfoss group companies. Danfoss and the Danfoss logo are trademarks of Danfoss A’S. All rights reserved.

Imibuzo ebuzwa qho

How can I adjust the reference setpoint on the controller?

Use the upper and lower buttons to adjust the reference setpoint. Be cautious not to unintentionally change settings.

Kwenzeka ntoni xa icompressor ibona uxinzelelo oluphantsi lokufunxa?

The internal low pressure monitoring function will cut out the compressor after a specified time delay if suction pressure falls below the lower limit, triggering an alarm (A2).

How does the fan speed operate during low loads?

At low loads between 10-30%, the fan speed remains constant at the level set in the 'FanMinSpeed' function.

Amaxwebhu / Izibonelelo

Danfoss Optyma Plus SW Ver. 3.7x Controller for Condensing Unit [pdf] Isikhokelo somsebenzisi Optyma Plus SW Ver. 3.7x Controller for Condensing Unit, Optyma Plus SW Ver. 3.7x, Controller for Condensing Unit, Condensing Unit, Controller

Iimbekiselo

• Incwadi yokusebenzisa