Faka i-Cisco Catalyst Network Interface Module
Eli candelo libonelela ngolwazi ngaphambi nangexesha lokufakwa kweCisco Catalyst Network Interface Modules (NIMs) kwiCisco Catalyst 8200 Series Edge Platforms.
Ngaphezuluview yeNethiwekhi yoNxibelelwano lweModyuli
The Cisco Catalyst Network Interface Module (NIM) is supported on Cisco Catalyst 8200 Series Edge Platforms.
These are the steps to install a NIM:
1. Khangela indawo ye-NIM kwindawo yolawulo.
2. Loosen the screws to remove NIM blank cover.
3. Faka i-NIM kwindawo yokubeka.
4. Qinisa izikrufu ukukhusela i-NIM kwindawo yokubeka.
These are the steps to remove a NIM:
1. If the NIM is up and running, issue the following command to shut down the NIM gracefully before removing it:
hw-module subslot slot 0/2 stop
Isilumkiso If you do not shut down the NIM gracefully before removing it, the NIM card could get damaged.
2. Khangela indawo ye-NIM kwindawo yolawulo.
3. Khulula izikrufu ezikhusela i-NIM.
4. Khupha ngobunono i-NIM kwindawo yokubeka.
All module slots must have a module or blank installed for the product to work thermally and for safety purposes.
Ngolwazi olongezelelweyo, jonga iCisco Catalyst 8200 Series Edge Platforms database kwi-cisco.com uluhlu lwee-NIM ezixhaswayo kumaqonga.
Susa kwaye ufake iiModyuli zoNxibelelwano lweNethiwekhi
Keep the following tools and equipment while working with the Network Interface Modules (NIM)s:
- Inombolo 1 Phillips screwdriver okanye i-screwdriver encinci ye-flat-blade
- I-ESD-yokuthintela umtya esihlahleni
Susa iModyuli yoNxibelelwano lweNethiwekhi
Inyathelo loku-1 Shut down the electrical power to the slot in the device, turn off the electrical power to the device. Leave the power cable plugged-in to channel ESD voltages emhlabeni.
Inyathelo loku-2 Remove all network cables from the rear panel of the device. Using a number 1 Phillips screwdriver, loosen the captive screws on the network interface module.
Inyathelo loku-3 Slide the network interface module out.
Inyathelo loku-4 If you are not replacing the module, install a blank faceplate over the empty slot to ensure proper air flow.
Faka iCisco Catalyst Network Interface Modules
Inyathelo loku-1 Shut down the electrical power to the slot in the router by turning off the electrical power to the router. Leave the power cable plugged in to channel ESD voltages emhlabeni.
Inyathelo loku-2 Remove all network cables from the rear panel of the device.
Inyathelo loku-3 Remove the blank faceplates installed over the network interface module slot that you intend to use.
Phawula Save blank faceplates for future use.
Inyathelo loku-4 Align the module with the guides in the chassis walls or slot divider and slide it gently into the NIM slot on the device.
Inyathelo loku-5 Push the module into place until you feel the edge connector seat securely into the connector on the router backplane. The module faceplate should contact the chassis rear panel.
Inyathelo loku-6 Using a number 1 Phillips screwdriver, tighten the captive screws on the network interface module.
Inyathelo loku-7 Connect the module to the network and re-enable the power to the slot in the device.
Faka i-Cisco Catalyst Network Interface Module
Amaxwebhu / Izibonelelo
 |
I-CISCO 8200 Series Catalyst Network Interface Module [pdf] Isikhokelo somsebenzisi 8200 Series, 8200 Series Catalyst Network Interface Module, Catalyst Network Interface Module, Network Interface Module, Interface Module |