ARDUINO AKX00034 Edge Control uMnini yoMnini
Inkcazo
Ibhodi yeArduino® Edge Control yenzelwe ukujongana neemfuno zokulima ngokuchanekileyo. Ibonelela ngenkqubo yokulawula amandla aphantsi, ilungele ukunkcenkceshela ngoqhagamshelwano lwemodyuli. Ukusebenza kwale bhodi kwandiswa kunye neeBhodi ze-Arduino® MKR ukubonelela ngoqhagamshelwano olongezelelweyo.
Iindawo ekujoliswe kuzo
Imilinganiselo yezolimo, iinkqubo zokunkcenkceshela ezihlakaniphile, i-hydroponics
Iimbonakalo
INina B306 Imodyuli
Iprosesa
- 64 MHz Arm® Cortex®-M4F (neFPU)
- 1 MB Flash + 256 KB RAM
Wireless
- IBluetooth (BLE 5 ngeCordio® stack) Izandiso zeNtengiso
- 95 dBm ubuntununtunu
- 4.8 mA kwi-TX (0 dBm)
- 4.6 mA kwi-RX (1 Mbps)
Iiperipherals
- Isantya esipheleleyo 12 Mbps USB
- I-Arm® CryptoCell® CC310 isixokelelwano sokhuseleko se-QSPI/SPI/TWI/I²S/PDM/QDEC
- Isantya esiphezulu 32 MHz SPI
- I-Quad SPI interface 32 MHz
- I-12-bit 200 ksps ADC
- I-128 bit AES / ECB / CCM / AAR co-processor
Inkumbulo
- 1 MB yangaphakathi inkumbulo yeFlash
- 2MB kwibhodi ye-QSPI
- Ikhadi le-SD
Amandla
- Amandla aphantsi
- 200uA Ukulala ngoku
- Inokusebenza ukuya kuthi ga kwiinyanga ezingama-34 kwibhetri eyi-12V/5Ah
- I-12 V Acid/lead SLA Battery Supply (Itshajwa kwakhona ngeepaneli zesola) RTC CR2032 Lithium Battery back up
Ibhetri
- Itshaja yebhetri yeSolar LT3652
- Ubonelelo ngegalelo Voltage I-Regulation Loop yePeak Power Tracking kwi-(MPPT) izicelo zeSola
I/O
- 6x edge sensitive ukuvuka izikhonkwane
- I-16x igalelo le-watermark ye-watermark ye-hydrostatic
- 8x 0-5V igalelo analog
- 4x 4-20mA amagalelo
- 8x latching relay iziphumo zomyalelo nabaqhubi
- 8x latching relay iziphumo zomyalelo ngaphandle kwabaqhubi
- I-4x 60V/2.5A i-galvanically ibekwe yodwa izikhuseli zesimo esiqinileyo
- 6x 18 pin iplagi kwizihlanganisi block block
Iisokethi ezimbini zeMKR
- Ulawulo lwamandla omntu ngamnye
- Izibuko lothotho lomntu ngamnye
- Izibuko ze-I2C zomntu ngamnye
Ulwazi lokhuseleko
- Iklasi A
Ibhodi
Isicelo ExampLes
IArduino® Edge Control lisango lakho lokuya kwezoLimo 4.0. Fumana ulwazi lwexesha lokwenyani kwimeko yenkqubo yakho kwaye wandise isivuno sesityalo. Phucula ukusebenza kakuhle kweshishini ngokuzenzekela kunye nokulima kwangaphambili. Lungelelanisa uMda woLawulo ngokweemfuno zakho ngokusebenzisa iiBhodi ezimbini zeArduino® MKR kunye noluhlu lweeShields ezihambelanayo. Gcina iirekhodi zembali, ukulawula umgangatho ngokuzenzekelayo, sebenzisa ukucwangciswa kwezityalo, kunye nokunye nge-Arduino IoT Cloud ukusuka naphi na emhlabeni.
Greenhouses ezizenzekelayo
Ukuze kuncitshiswe ukukhutshwa kwekhabhoni kwaye kwandiswe isivuno sezoqoqosho, kubalulekile ukuqinisekisa ukuba eyona ndawo ilungileyo ibonelelwa ekukhuleni kwezityalo ngokufuma, ubushushu kunye nezinye izinto. Ulawulo lwe-Arduino® Edge luyiqonga elidibeneyo elenza ukuba iliso elikude kunye nokulungiswa kwexesha langempela ukuza kuthi ga ngoku. Ukuquka i-Arduino® MKR GPS Shield (SKU: ASX00017) ivumela ukucwangciswa kokujikeleziswa kwezityalo kunye nokufumana idatha ye-geospatial.
Hydroponics / Aquaponics
Kuba i-hydroponics ibandakanya ukukhula kwezityalo ngaphandle komhlaba, kufuneka kugcinwe ukhathalelo oluthambileyo ukuze kuqinisekiswe ukuba zigcina ifestile emxinwa efunekayo ukuze zikhule ngokugqibeleleyo. I-Arduino Edge Control inokuqinisekisa ukuba le festile ifezekiswa ngomsebenzi omncinci wezandla. I-Aquaponics inokubonelela ngeenzuzo ezingaphezulu kuneziqhelekileyo ze-hydroponics apho iArduino®'s Edge Control inokunceda ukuhambelana neemfuno eziphezulu ngakumbi ngokubonelela ngolawulo olungcono kwinkqubo yangaphakathi ngelixa ekugqibeleni inciphisa imingcipheko yemveliso.
Ukulinywa kwamakhowa: Amakhowa adume kakubi ngokufuna iqondo lobushushu eligqibeleleyo kunye neemeko zokufuma ukuze agcine ukukhula kwembewu ngelixa ethintela ukukhula komngundo. Ndiyabulela kwiinzwa ezininzi ze-watermark, izibuko eziphumayo, kunye nokhetho lokuqhagamshelwa olukhoyo kwi-Arduino® Edge Control kunye ne-Arduino® IoT Cloud, oku kufama ngokuchanekileyo kunokufezekiswa kwinqanaba elingazange libonwe ngaphambili.
Izincedisi.
- I-Irrometer Tensiometers
- Izivamvo zokufuma komhlaba ze-Watermark
- Iivalvu zebhola ezimatshini
- Iphaneli yelanga
- 12V/5Ah acid/lead SLA ibhetri (11 – 13.3V)
Iimveliso ezinxulumeneyo
- Isiboniso se-LCD + iCable Flat + indawo ebiyelweyo yeplastiki
- 1844646 abafowunelwa basePhoenix (ibandakanyiwe nemveliso)
- Iibhodi zosapho zeArduino® MKR (zokwandisa uqhagamshelo olungenazingcingo)
Isisombululo phezuview
Example yesicelo esiqhelekileyo sesisombululo esiquka i-LCD Display kunye neebhodi ezimbini ze-Arduino® MKR 1300.
Amanqaku
IiReyithingi eziphezulu ezipheleleyo
| Uphawu | Inkcazo | Min | Chwetheza | Max | Iyunithi |
| TMax | Ubuninzi bomlinganiselo we-thermal | -40 | 20 | 85 | °C |
| VBattMax | Ubuninzi begalelo voltage ukusuka kwigalelo lebhetri | -0.3 | 12 | 17 | V |
| VSolarMax | Ubuninzi begalelo voltage ukusuka kwiphaneli yelanga | -20 | 18 | 20 | V |
| ARelayMax | Ubuninzi bangoku ngokutshintshwa kwe-relay | - | - | 2.4 | A |
| PMax | UkuSetyenziswa kwamandla aphezulu | - | - | 5000 | mW |
IiMeko zokuSebenza eziCetyisiweyo
| Uphawu | Inkcazo | Min | Chwetheza | Max | Iyunithi |
| T | Imida yokushisa egciniweyo | -15 | 20 | 60 | °C |
| VBatt | Igalelo voltage ukusuka kwigalelo lebhetri | - | 12 | - | V |
| VSolar | Igalelo voltage ukusuka kwiphaneli yelanga | 16 | 18 | 20 | V |
Umsebenzi oPhezuluview
I-Topology yeBhodi
Phezulu View
| Ref. | Inkcazo | Ref. | Inkcazo |
| U1 | LT3652HV itshaja yebhetri IC | J3,7,9,8,10,11 | Iibhloko ze-terminal ezi-1844798 eziplagayo |
| U2 | MP2322 3.3V isiguquli sebhanti IC | I-LED1 | Kwibhodi ye-LED |
| U3 | I-MP1542 19V yokunyusa i-converter IC | PB1 | Seta kwakhona iqhosha lokutyhala |
| U4 | TPS54620 5V yokunyusa isiguquli IC | J6 | Micro SD Card |
| U5 | I-CD4081BNSR KUNYE nesango le-IC | J4 | CR2032 isibambi sebhetri |
| U6 | I-CD40106BNSR AYIKHO isango le-IC | J5 | I-Micro USB (NINA Modyuli) |
| U12,U17 | I-MC14067BDWG i-multiplexer IC | U8 | TCA6424A IO isandisi IC |
| U16 | CD40109BNSRG4 I/O Expander | U9 | Imodyuli ye-NINA-B306 |
| U18,19,20,21 | I-TS13102 isilayidi sesimo esiluqilima IC | U10 | ADR360AUJZ-R2 Voltage reference series 2.048V IC |
| Ref. | Inkcazo | Ref. | Inkcazo |
| U11 | W25Q16JVZPIQ Flash 16M IC | Q3 | ZXMP4A16GTA MOSFET P-CH 40V 6.4A |
| U7 | I-CD4081BNSR KUNYE nesango le-IC | U14, 15 | MC14067BDWG IC MUX |
Iprosesa
IProsesa ePhambili yiCortex M4F esebenza ukuya kuthi ga kwi-64MHz.
Isikrini se-LCD
I-Arduino® Edge Control inikeza ikhonkco elizinikeleyo (J1) lokudibanisa kunye ne-HD44780 16 × 2 imodyuli yokubonisa i-LCD, ethengiswa ngokwahlukileyo. Iprosesa ephambili ilawula i-LCD nge-TCA6424 port expander ngaphezu kwe-I2C. Idatha idluliswa kwi-interface ye-4-bit. Ukuqina kokukhanya kwe-LCD kwakhona kuhlengahlengiswa yiprosesa ephambili.
I-5V ye-Analog Sensors
Ukuya kuthi ga kwisibhozo se-0-5V ye-analog inputs inokudityaniswa kwi-J4 ye-interfacing analog sensors ezifana ne-tensiometers kunye ne-dendrometers. Amagalelo akhuselwe yi-19V Zener diode. Igalelo ngalinye liqhagamshelwe kwi-multiplexer ye-analog ehambisa umqondiso kwi-port enye ye-ADC. Igalelo ngalinye liqhagamshelwe kwi-analog multiplexer (MC14067) ehambisa umqondiso kwi-port eyodwa ye-ADC. Iprosesa ephambili ilawula ukhetho lwegalelo nge-TCA6424 port expander phezu kwe-I2C.
4-20mA iiSensors
Ukuya kuthi ga kwii-4-20mA ezine sensors zinokudityaniswa kwi-J4. Umqulu wereferensitagI-e ye-19V iveliswa yi-MP1542 inyathelo-up converter ukunika amandla i-loop yangoku. Ixabiso loluvo lifundwa nge-220 ohm resistor. Igalelo ngalinye liqhagamshelwe kwi-analog multiplexer (MC14067) ehambisa umqondiso kwi-port eyodwa ye-ADC. Iprosesa ephambili ilawula ukhetho lwegalelo nge-TCA6424 port expander phezu kwe-I2C.
Iinzwa zeWatermark
Ukuya kuthi ga kwishumi elinesithandathu i-hydrostatic sensors ye-watermark inokudityaniswa kwi-J8. Izikhonkwane ze-J8-17 kunye ne-J8-18 ziyizikhonkwane eziqhelekileyo kuzo zonke izinzwa, ezilawulwa ngokuthe ngqo kwi-microcontroller. Amagalelo kunye nezikhonkwane eziqhelekileyo zenzwa zikhuselwe yi-19V Zener diode. Igalelo ngalinye liqhagamshelwe kwi-analog multiplexer (MC14067) ehambisa umqondiso kwi-port eyodwa ye-ADC. Iprosesa ephambili ilawula ukhetho lwegalelo nge-TCA6424 port expander phezu kwe-I2C. Ibhodi isekela iindlela ezi-2 ezichanekileyo.
UkuLatching Iziphumo
Iziqhagamshelo i-J9 kunye ne-J10 zibonelela ngeziphumo kwizixhobo zokubambelela ezifana neevalvu ezihamba ngeenjini. Imveliso yokuxhoma iqulathe amajelo amabini (P kunye no-N) apho impembelelo okanye istrobe inokuthunyelwa kuyo nayiphi na itshaneli ezi-2 (ukuvula ivalve evalayo ye ex.ample). Ubude be-strobes bunokulungiswa ukuze kulungiswe imfuno yesixhobo sangaphandle. Ibhodi ibonelela ngamazibuko ali-16 ewonke ahlulwe ngokweendidi ezi-2:
- Imiyalelo yokuLatching (J10): I-8 izibuko zokufakelwa kwe-impedance ephezulu (max +/- 25 mA). Qhagamshela kwizixhobo zangaphandle ezinokhuseleko lomntu wesithathu / iisekethe zamandla. Kubhekiselwa kwi-VBAT.
- I-Latching Out (J9): izibuko ezi-8. Oku ziphumo kubandakanya abaqhubi isixhobo latching. Akukho baqhubi bangaphandle abafunekayo. Kubhekiselwa kwi-VBAT.
Ugqithiso lweLizwe eliQilileyo
Ibhodi ibonakalisa ezine ezilungisekayo 60V 2.5A iilayidi zesimo esiqinileyo kunye negalvanic isolation ekhoyo kwi-J11. Usetyenziso oluqhelekileyo lubandakanya i-HVAC, ulawulo lokutshiza njl.
Ugcino
Ibhodi ibandakanya zombini i-socket yekhadi le-microSD kunye nememori ye-flash eyongezelelweyo ye-2MB yokugcina idatha. Zombini ziqhagamshelwe ngokuthe ngqo kwiprosesa ephambili nge-SPI interface.
Umthi wamandla
Ibhodi inokuthi inikwe amandla ngeepaneli zelanga kunye/okanye neebhetri ze-SLA.
Ukusebenza kweBhodi
Ukuqalisa – IDE
Ukuba ufuna ukucwangcisa iArduino® Edge Control yakho ngelixa ungaxhunyiwe kufuneka ufakele iArduino® Desktop IDE [1] Ukuqhagamshela iArduino® Edge control kwikhompyuter yakho, uya kudinga intambo ye-USB eyiMicro-B. Oku kunika amandla ebhodini, njengoko kuboniswe yi-LED.
Ukuqalisa - Arduino Web Umhleli
Zonke iibhodi zeArduino®, kuquka nale, zisebenza ngaphandle kwebhokisi kwiArduino® Web Umhleli [2], ngokufaka nje iplagi elula. IArduino® Web Umhleli ubanjwa kwi-intanethi, ke ngoko iya kuhlala isexesheni ngeempawu zamva nje kunye nenkxaso yazo zonke iibhodi. Landela [3] ukuqalisa ukubhala ikhowudi kwisikhangeli kwaye ulayishe imizobo yakho ebhodini yakho.
Ukuqalisa-i-Arduino IoT Cloud
Zonke iimveliso ezinikwe amandla ze-Arduino® IoT zixhaswa kwi-Arduino® IoT Cloud ekuvumela ukuba uLog, igrafu kwaye uhlalutye idatha yenzwa, uqalise imicimbi, kwaye wenze ngokuzenzekelayo ikhaya lakho okanye ishishini.
Sample Sketches
Sampimizobo yeArduino® Edge Control inokufumaneka nokuba ku “Examples” kwimenyu yeArduino® IDE okanye kwicandelo elithi “Amaxwebhu” kwiArduino® Pro webindawo [4]
Izixhobo ezikwi-Intanethi
Ngoku ukuba udlule kwizinto ezisisiseko onokuthi uzenze ngebhodi ungaphonononga amathuba angenasiphelo ebonelela ngokujonga iiprojekthi ezinomdla kwiProjectHub [5], iArduino® Library Reference [6] kunye nevenkile ekwi-intanethi [7] apho Uya kuba nakho ukuncedisa ibhodi yakho ngeenzwa, ii-activators kunye nokunye.
UkuBuyiselwa kweBhodi
Zonke iibhodi zeArduino® zine-bootloader eyakhelwe-ngaphakathi evumela ukuba ibhodi ivuleke nge-USB. Kwimeko apho umzobo utshixa iprosesa kwaye ibhodi ayifumaneki kwakhona nge-USB kunokwenzeka ukuba ungene kwimowudi yokuqalisa ngokucofa kabini iqhosha lokuseta kwakhona emva kokunyusa amandla.
Izikhonkwane zoDibaniso
J1 LCD Isidibanisi
| Iphini | Umsebenzi | Uhlobo | Inkcazo |
| 1 | PWM | Amandla | Isibane se-LED Cathode (ulawulo lwe-PWM) |
| 2 | Vula amandla | Idijithali | Ungeniso lweqhosha |
| 3 | +5V LCD | Amandla | LCD amandla ombane |
| 4 | LCD RS | Idijithali | LCD RS uphawu |
| 5 | Ukuthelekisa | I-Analog | Ulawulo lokuchasana kweLCD |
| 6 | LCD RW | Idijithali | LCD Funda/Bhala uphawu |
| 7 | I-LED + | Amandla | Ukukhanya kwe-LED Anode |
| 8 | LCD EN | Idijithali | LCD Vulela isiginali |
| 10 | LCD D4 | Idijithali | Umqondiso we-LCD D4 |
| 12 | LCD D5 | Idijithali | Umqondiso we-LCD D5 |
| 14 | LCD D6 | Idijithali | Umqondiso we-LCD D6 |
| 16 | LCD D7 | Idijithali | Umqondiso we-LCD D7 |
| 9,11,13,15 | GND | Amandla | Umhlaba |
Imiqondiso ye-J3 yokuvuka/iMiyalelo yoKugqithiselwa kwaNgaphandle
| Iphini | Umsebenzi | Uhlobo | Inkcazo |
| 1,3,5,7,9 | V BAT | Amandla | Gated voltagibhetri yereferensi yomqondiso wokuvuka |
| 2,4,6,8,10,12 | Igalelo | Idijithali | Iimpawu zokuvuka ezibuthathaka |
| 13 | Isiphumo | Idijithali | Isignali yewotshi yewotshi eqinileyo yangaphandle 1 |
| 14 | Isiphumo | Idijithali | Isignali yewotshi yewotshi eqinileyo yangaphandle 2 |
| 17 | Bidir | Idijithali | Isignali yedatha yesimo esiluqilima sangaphandle 1 |
| 18 | Bidir | Idijithali | Isignali yedatha yesimo esiluqilima sangaphandle 2 |
| 15,16 | GND | Amandla | Umhlaba |
J5 USB
| Iphini | Umsebenzi | Uhlobo | Inkcazo |
| 1 | I-VUSB | Amandla | Inqaku loNgeniso loMbane: Ibhodi enikwe amandla kuphela nge-V USB ayisayi kwenza uninzi lweempawu zebhodi. Jonga umthi wamandla kwiCandelo 3.8 |
| 2 | D- | Ezahlukileyo | Idatha eyahlukileyo ye-USB- |
| 3 | D+ | Ezahlukileyo | Idatha eyahlukileyo ye-USB + |
| 4 | ID | NC | Engasetyenziswanga |
| 5 | GND | Amandla | Umhlaba |
I-J7 Analog / 4-20mA
| Iphini | Umsebenzi | Uhlobo | Inkcazo |
| 1,3,5,7 | +19V | Amandla | 4-20mA voltage reference |
| 2 | IN1 | I-Analog | 4-20mA igalelo 1 |
| 4 | IN2 | I-Analog | 4-20mA igalelo 2 |
| 6 | IN3 | I-Analog | 4-20mA igalelo 3 |
| 8 | IN4 | I-Analog | 4-20mA igalelo 4 |
| 9 | GND | Amandla | Umhlaba |
| 10 | +5V | Amandla | Imveliso ye-5V yereferensi ye-analog ye-0-5V |
| 11 | A5 | I-Analog | 0-5V igalelo 5 |
| 12 | A1 | I-Analog | 0-5V igalelo 1 |
| 13 | A6 | I-Analog | 0-5V igalelo 6 |
| 14 | A2 | I-Analog | 0-5V igalelo 2 |
| 15 | A7 | I-Analog | 0-5V igalelo 7 |
| 16 | A3 | I-Analog | 0-5V igalelo 3 |
| 17 | A8 | I-Analog | 0-5V igalelo 8 |
| 18 | A4 | I-Analog | 0-5V igalelo 4 |
J8 iWatermark
| Iphini | Umsebenzi | Uhlobo | Inkcazo |
| 1 | AmanziMrk1 | I-Analog | Igalelo leWatermark 1 |
| 2 | AmanziMrk2 | I-Analog | Igalelo leWatermark 2 |
| 3 | AmanziMrk3 | I-Analog | Igalelo leWatermark 3 |
| 4 | AmanziMrk4 | I-Analog | Igalelo leWatermark 4 |
| 5 | AmanziMrk5 | I-Analog | Igalelo leWatermark 5 |
| 6 | AmanziMrk6 | I-Analog | Igalelo leWatermark 6 |
| 7 | AmanziMrk7 | I-Analog | Igalelo leWatermark 7 |
| 8 | AmanziMrk8 | I-Analog | Igalelo leWatermark 8 |
| 9 | AmanziMrk9 | I-Analog | Igalelo leWatermark 9 |
| 10 | AmanziMrk10 | I-Analog | Igalelo leWatermark 10 |
| 11 | AmanziMrk11 | I-Analog | Igalelo leWatermark 11 |
| 12 | AmanziMrk12 | I-Analog | Igalelo leWatermark 12 |
| 13 | AmanziMrk13 | I-Analog | Igalelo leWatermark 13 |
| 14 | AmanziMrk14 | I-Analog | Igalelo leWatermark 14 |
| Iphini | Umsebenzi | Uhlobo | Inkcazo |
| 15 | AmanziMrk15 | I-Analog | Igalelo leWatermark 15 |
| 16 | AmanziMrk16 | I-Analog | Igalelo leWatermark 16 |
| 17,18 | VCOMMON | Idijithali | Uluvo oluqhelekileyo voltage |
I-J9 Latching Out (+/- VBAT)
| Iphini | Umsebenzi | Uhlobo | Inkcazo |
| 1 | PULSE_OUT0_P | Idijithali | Latching isiphumo 1 positive |
| 2 | PULSE_OUT0_N | Idijithali | I-Latching output 1 negative |
| 3 | PULSE_OUT1_P | Idijithali | Latching isiphumo 2 positive |
| 4 | PULSE_OUT1_N | Idijithali | I-Latching output 2 negative |
| 5 | PULSE_OUT2_P | Idijithali | Latching isiphumo 3 positive |
| 6 | PULSE_OUT2_N | Idijithali | I-Latching output 3 negative |
| 7 | PULSE_OUT3_P | Idijithali | Latching isiphumo 4 positive |
| 8 | PULSE_OUT3_N | Idijithali | I-Latching output 4 negative |
| 9 | PULSE_OUT4_P | Idijithali | Latching isiphumo 5 positive |
| 10 | PULSE_OUT4_N | Idijithali | I-Latching output 5 negative |
| 11 | PULSE_OUT5_P | Idijithali | Latching isiphumo 6 positive |
| 12 | PULSE_OUT5_N | Idijithali | I-Latching output 6 negative |
| 13 | PULSE_OUT6_P | Idijithali | Latching isiphumo 7 positive |
| 14 | PULSE_OUT6_N | Idijithali | I-Latching output 7 negative |
| 15 | PULSE_OUT7_P | Idijithali | Latching isiphumo 8 positive |
| 16 | PULSE_OUT7_N | Idijithali | I-Latching output 8 negative |
| 17,18 | GND | Amandla | Umhlaba |
J10 Latching Command (+/- VBAT)
| Iphini | Umsebenzi | Uhlobo | Inkcazo |
| 1 | STOBE8_P | Idijithali | I-Latching command 1 positive |
| 2 | STOBE8_N | Idijithali | Ukubamba umyalelo 1 ongalunganga |
| 3 | STOBE9_P | Idijithali | I-Latching command 2 positive |
| 4 | STOBE9_N | Idijithali | Ukubamba umyalelo 2 ongalunganga |
| 5 | STOBE10_P | Idijithali | I-Latching command 3 positive |
| 6 | STOBE10_N | Idijithali | Ukubamba umyalelo 3 ongalunganga |
| 7 | STOBE11_P | Idijithali | I-Latching command 4 positive |
| 8 | STOBE11_N | Idijithali | Ukubamba umyalelo 4 ongalunganga |
| 9 | STOBE12_N | Idijithali | I-Latching command 5 positive |
| 10 | STOBE12_P | Idijithali | Ukubamba umyalelo 5 ongalunganga |
| 11 | STOBE13_P | Idijithali | I-Latching command 6 positive |
| 12 | STOBE13_N | Idijithali | Ukubamba umyalelo 6 ongalunganga |
| 13 | STOBE14_P | Idijithali | I-Latching command 7 positive |
| 14 | STOBE14_N | Idijithali | Ukubamba umyalelo 7 ongalunganga |
| 15 | STOBE15_P | Idijithali | I-Latching command 8 positive |
| 16 | STOBE15_N | Idijithali | Ukubamba umyalelo 8 ongalunganga |
| Iphini | Umsebenzi | Uhlobo | Inkcazo |
| 17 | GATED_VBAT_PULSE | Amandla | IGated Positive terminal yebhetri |
| 18 | GND | Amandla | Umhlaba |
I-J11 Relay (+/- VBAT)
| Iphini | Umsebenzi | Uhlobo | Inkcazo |
| 1 | SOLAR+ | Amandla | I-Solar Panel Positive Terminal |
| 2 | NC | NC | Engasetyenziswanga |
| 3 | GND | Amandla | Umhlaba |
| 4 | RELAY1_P | Tshintsha | Relay 1 positive |
| 5 | NC | NC | Engasetyenziswanga |
| 6 | RELAY1_N | Tshintsha | Relay 1 negative |
| 7 | NC | NC | Engasetyenziswanga |
| 8 | RELAY2_P | Tshintsha | Relay 2 positive |
| 9 | NC | NC | Engasetyenziswanga |
| 10 | RELAY2_N | Tshintsha | Relay 2 negative |
| 11 | 10kGND | Amandla | Umhlaba nge-10k resistor |
| 12 | RELAY3_P | Tshintsha | Relay 3 positive |
| 13 | NTC | I-Analog | Ubushushu obunegative coeffcient (NTC) thermoresistor |
| 14 | RELAY3_N | Tshintsha | Relay 3 negative |
| 15 | GND | Amandla | Umhlaba |
| 16 | RELAY4_P | Tshintsha | Relay 4 positive |
| 17 | IBHATHI+ | Amandla | Itheminali eKhona ibhetri |
| 18 | RELAY4_N | Tshintsha | Relay 4 negative |
Ulwazi ngoomatshini
Ulwandlalo lweBhodi
Imingxunya yokuNzeka
Izikhundla zokuqhagamshela
Iziqinisekiso
Sibhengeza phantsi koxanduva lwethu ukuba ezi mveliso zingentla zihambelana neemfuno ezingundoqo zale Miqathango ilandelayo ye-EU kwaye ke ngoko sikulungele ukuhamba ngokukhululekileyo kwiimarike ezibandakanya iManyano yaseYurophu (i-EU) kunye noMmandla woQoqosho waseYurophu (EEA).
Isibhengezo sokuThobela kwi-EU RoHS & REACH 211 01/19/2021
Iibhodi ze-Arduino zihambelana ne-RoHS 2 Directive 2011/65/EU yePalamente yaseYurophu kunye ne-RoHS 3 Directive 2015/863/EU yeBhunga le-4 kaJuni 2015 ekuthinteleni ukusetyenziswa kwezinto ezithile ezinobungozi kwisixhobo sombane kunye ne-elektroniki.
| Iziyobisi | Ubuninzi bomda (ppm) |
| Khokela (Pb) | 1000 |
| I-Cadmium (Cd) | 100 |
| Imercury (HG) | 1000 |
| Hexavalent Chromium (Cr6+) | 1000 |
| Iibiphenyls zePoly Brominated (PBB) | 1000 |
| I-Poly Brominated Diphenyl ethers (PBDE) | 1000 |
| I-Bis(2-Ethylhexyl} phthalate (DEHP) | 1000 |
| I-Benzyl butyl phthalate (BBP) | 1000 |
| I-Dibutyl phthalate (DBP) | 1000 |
| I-Diisobutyl phthalate (DIBP) | 1000 |
Ukukhululwa : Akukho kukhululwa kubangwayo.
Iibhodi ze-Arduino zihambelana ngokupheleleyo neemfuno ezihambelanayo ze-European Union Regulation (EC) 1907 / 2006 malunga noBhaliso, uVavanyo, uGunyaziso kunye nokuThintelwa kweMichiza (REACH). Sibhengeza ukuba akukho nanye kwii-SVHCs (https://echa.europa.eu/web/undwendwe/itheyibhile yoluhlu lwabagqatswa), uLuhlu lwaBaviwa beZinto eziNxibeleleyo ngokuPhakamileyo ngokugunyaziswa ngoku ekhutshwe yi-ECHA, ikhona kuzo zonke iimveliso (kunye nepakethe) ngobuninzi obupheleleyo kuxinzelelo olulingana okanye ngaphezulu kwe-0.1%. Ngokolwazi lwethu, sikwabhengeza ukuba iimveliso zethu aziqulathanga naziphi na izinto ezidweliswe “kuLuhlu loGunyaziso” (Isihlomelo XIV semigaqo ye-REACH) kunye nezinto eziXhathayo kakhulu (SVHC) kuyo nayiphi na imali ebalulekileyo njengoko kuchaziwe. ngoluhlu lweSihlomelo XVII soluhlu lwabaMviwa olupapashwe yi-ECHA (i-Arhente yeMichiza yaseYurophu) 1907 /2006/EC.
Ungquzulwano lweZimbiwa isibhengezo
Njengomboneleli wehlabathi jikelele wezinto zombane kunye nezombane, iArduino iyazazi izibophelelo zethu ngokubhekiselele kwimithetho nemimiselo ephathelele kwiConflict Minerals, ngokukodwa iDodd-Frank Wall Street Reform kunye noMthetho woKhuseleko lwaBathengi, iCandelo 1502. IArduino ayiveli ngqo okanye iqhube ukungquzulana ngokuthe ngqo. iiminerali ezifana neTin, iTantalum, iTungsten, okanye iGolide. Iiminerali eziphikisanayo ziqulethwe kwiimveliso zethu ngendlela yesolder, okanye njengenxalenye yealloys zetsimbi. Njengenxalenye yenkuthalo yethu efanelekileyo, i-Arduino iqhagamshelane nabanikezeli becandelo ngaphakathi kwekhonkco lethu lobonelelo ukuze baqinisekise ukuqhubeka kwabo nokuthobela imimiselo. Ngokusekelwe kulwazi esilufumeneyo ukuza kuthi ga ngoku, sibhengeza ukuba iimveliso zethu zinezimbiwa eziNgqubuthelana ezithathwe kwiindawo ezingenazingxabano.
Isilumkiso seFCC
Naluphi na uTshintsho okanye uhlengahlengiso olungavunywanga ngokucacileyo liqela elinoxanduva lokuthobela lunokutshitshisa igunya lomsebenzisi lokusebenzisa isixhobo.
Esi sixhobo sithobela inxalenye ye-15 yeMithetho yeFCC. Umsebenzi uxhomekeke kwezi meko zimbini zilandelayo:
- Esi sixhobo sisenokungabangeli uphazamiseko oluyingozi
- Esi sixhobo kufuneka samkele naluphi na uphazamiseko olufunyenweyo, kuquka uphazamiseko olunokubangela usetyenziso olungafunekiyo.
INkcazo yeFCC RF yokuVela kwiMitha:
- Esi siThuthi akufuneki sibe kwindawo enye okanye sisebenze kunye nayo nayiphi na enye i-eriyali okanye isidluliseli.
- Esi sixhobo sithobela imida yokuvezwa kwemitha ye-RF emiselwe indawo engalawulwayo.
- Esi sixhobo kufuneka sifakwe kwaye sisebenze umgama ongaphantsi kwama-20cm phakathi kweradiyetha kunye nomzimba wakho.
IsiNgesi: Iincwadana zabasebenzisi zezixhobo zerediyo ezikhululwe kwilayisenisi ziya kuqulatha oku kulandelayo okanye isaziso esifanayo kwindawo ecacileyo kwincwadi yomsebenzisi okanye ngenye indlela kwisixhobo okanye zombini. Esi sixhobo sithobela i(s) kumgangatho we-RSS woShishino lwaseKhanada. Umsebenzi uxhomekeke kwezi meko zimbini zilandelayo:
- Esi sixhobo sisenokungabangeli ukuphazamiseka
- Esi sixhobo kufuneka samkele naluphi na uphazamiseko, kuquka uphazamiseko olunokubangela ukusebenza okungafunekiyo kwesixhobo.
Isilumkiso se-IC SAR
IsiXhosa Esi sixhobo kufuneka sifakwe kwaye sisebenze kumgama ongaphantsi kwama-20 cm phakathi kweradiyetha kunye nomzimba wakho.
Kubalulekile: Ubushushu bokusebenza kwe-EUT abunakudlula kwi-85℃ kwaye akufunekanga bube ngaphantsi kwe -40℃.
| Iibhendi zokuphindaphinda | Awona mandla emveliso aphezulu (ERP) |
| 2402-2480Mhz | 3.35 dBm |
Ngale ndlela, i-Arduino Srl ibhengeza ukuba le mveliso iyahambelana neemfuno ezibalulekileyo kunye namanye amalungiselelo afanelekileyo oMgaqo ka-201453/EU. Le mveliso ivumelekile ukuba isetyenziswe kuwo onke amazwe angamalungu e-EU.
Ulwazi lweNkampani
| Igama leKhampani | Arduino Srl |
| Idilesi yeNkampani | Via Andrea Appiani 25, 20900 Monza, Italy |
Amaxwebhu ekubhekiswa kuwo
| Ref | Ikhonkco |
| Arduino® IDE (Desktop) | https://www.arduino.cc/en/Main/Software |
| Arduino® IDE (Cloud) | https://create.arduino.cc/editor |
| Arduino® Cloud IDE Ukuqalisa | https://create.arduino.cc/projecthub/Arduino_Genuino/getting-started-with- arduino-web-editor-4b3e4a |
| Arduino® Pro Webindawo | https://www.arduino.cc/pro |
| I-Hub yeProjekthi | https://create.arduino.cc/projecthub?by=part&part_id=11332&sort=trending |
| Isalathiso seThala leeNcwadi | https://github.com/bcmi- labs/Arduino_EdgeControl/tree/4dad0d95e93327841046c1ef80bd8b882614eac8 |
| Ivenkile ye-Intanethi | https://store.arduino.cc/ |
Guqula ilog
| Umhla | Uhlaziyo | Iinguqu |
| 21/02/2020 | 1 | Ukukhutshwa kokuqala |
| 04/05/2021 | 2 | Uhlaziyo loyilo/ulwakhiwo |
| 30/12/2021 | 3 | Uhlaziyo lolwazi |
Amaxwebhu / Izibonelelo
 |
ARDUINO AKX00034 Edge Control [pdf] Incwadi yoMnini AKX00034, 2AN9S-AKX00034, 2AN9SAKX00034, AKX00034 Edge Control, Edge Control |
