I-Arduino ABX00069 Nano 33 BLE Sense Rev2 3.3V AI iBhodi enikwe amandla
Iimbonakalo
- NINA B306 Imodyuli
- Iprosesa
- 64 MHz Arm® Cortex®-M4F (neFPU)
- 1 MB Flash + 256 kB RAM
- I-Bluetooth® 5 yerediyo yeeprotocol ezininzi
- 2 Mbps
- CSA #2
- Izandiso zentengiso
- Uluhlu olude
- +8 dBm TX amandla
- -95 dBm ubuntununtunu
- 4.8 mA kwi-TX (0 dBm)
- 4.6 mA kwi-RX (1 Mbps)
- Ibhaluni edityanisiweyo ene-50 Ω isiphumo esiphela-nye
- IEEE 802.15.4 inkxaso yerediyo
- Umsonto
- Zigbee
- Iiperipherals
- Isantya esipheleleyo 12 Mbps USB
- NFC-A tag
- Arm CryptoCell CC310 subsystem yokhuseleko
- QSPI/SPI/TWI/I²S/PDM/QDEC
- Isantya esiphezulu 32 MHz SPI
- I-Quad SPI interface 32 MHz
- I-EasyDMA yazo zonke ii-interfaces zedijithali
- I-12-bit 200 ksps ADC
- I-128 bit AES / ECB / CCM / AAR co-processor
- I-BMI270 I-6-axis IMU (i-Accelerometer kunye ne-Gyroscope) i-16-bit
- I-3-axis accelerometer ene-±2g/±4g/±8g/±16g uluhlu
- I-3-axis gyroscope ene-±125dps/±250dps/±500dps/±1000dps/±2000dps uluhlu
- BMM150 3-axis IMU (Magnetometer)
- I-3-axis digital geomagnetic sensor
- 0.3μT isisombululo
- ±1300μT (x,y-axis), ±2500μT (z-axis)
- I-LPS22HB (Ibarometer kunye nesivamvo sobushushu)
- I-260 ukuya kwi-1260 hPa uluhlu olupheleleyo loxinzelelo kunye ne-24 bit echanekileyo
- Ikhono loxinzelelo oluphezulu: i-20x epheleleyo
- Imbuyekezo yobushushu efakiweyo
- I-16-bit imveliso yedatha yobushushu
- I-1 Hz ukuya kuma-75 Hz ireyithi yokuphuma kwedathaPhazamisa imisebenzi: iDatha eLungileyo, iiflegi zeFIFO, imida yoxinzelelo
- HS3003 Ubushushu kunye noluvo lokufuma
- 0-100% uluhlu lokufuma olunxulumeneyo
- Ukuchaneka kokufuma: ±1.5%RH, eqhelekileyo (HS3001, 10 ukuya kwi-90%RH,25°C)
- Ukuchaneka kwenzwa yobushushu: ± 0.1 ° C, eqhelekileyo
- Ukuya kuthi ga kwi-14-bit ukufuma kunye nedatha yemveliso yobushushu
- I-APDS-9960 (Ukusondela kweDigital, ukukhanya okukuyo, iRGB kunye neSensor yeGesture)
- Ukukhanya kwe-Ambient kunye ne-RGB yokubona uMbala nge-UV kunye nezihluzo ezithintelayo ze-IR
- Uvakalelo oluphezulu kakhulu - Ilungele ukusebenza emva kweglasi emnyama
- Ukuziva kufutshane kunye noKwaliwa kokuKhanya okukwi-Ambient
- Ukuva intshukumo yentshukumo entsonkothileyo
- IMP34DT06JTR (Imayikrofoni yeDijithali)
- I-AOP = 122.5 dbSPL
- I-64 dB isignali-kwingxolo yomlinganiselo
- Uvakalelo lwamacala onke
- -26 dBFS ± 3 dB ubuntununtunu
- MP2322 DC-DC
- Ulawula igalelo voltage ukusuka ukuya kuthi ga kwi-21V kunye nobuncinci be-65% ukusebenza kakuhle @ @umthwalo omncinci
- Ngaphezulu kwe-85% esebenzayo @12V
- Iprosesa
INGCACISO YEMVELISO
Ibhodi
Njengazo zonke iibhodi ze-Nano form factor, iNano 33 BLE Sense Rev2 ayinayo itshaja yebhetri kodwa inokunikwa amandla nge-USB okanye ngeeheader.
PHAWULA: I-Nano 33 BLE Sense Rev2 ixhasa kuphela i-3.3VI / Os kwaye AKUKHO ukunyamezela kwe-5V ngoko ke nceda uqinisekise ukuba awuqhagamshelani ngqo iimpawu ze-5V kule bhodi okanye iya konakala. Kwakhona, ngokuchaseneyo neebhodi ze-Arduino Nano ezixhasa ukusebenza kwe-5V, iphini ye-5V ayiboneleli ngevolthi.tage kodwa iqhagamshelwe, nge-jumper, kwigalelo lamandla e-USB.
Amanqaku
IiMeko zokuSebenza eziCetyisiweyo
| Uphawu | Inkcazo | Min | Max |
| Imida yogcino yobushushu yebhodi yonke: | -40 °C ( 40 °F) | 85°C ( 185 °F) |
Ukutya umbane
| Uphawu | Inkcazo | Min | Chwetheza | Max | Iyunithi |
| PBL | Ukusetyenziswa kwamandla kunye ne-loop exakekile | TBC | mW | ||
| PLP | Ukusetyenziswa kwamandla kwimowudi yamandla aphantsi | TBC | mW | ||
| PMAX | UkuSetyenziswa kwamandla aphezulu | TBC | mW |
Umsebenzi oPhezuluview
I-Topology yeBhodi
Phezulu:
Itopology yebhodi ephezulu
| Ref. | Inkcazo | Ref. | Inkcazo |
| U1 | I-NINA-B306 Imodyuli yeBluetooth® Amandla aphantsi 5.0 Imodyuli | U6 | MP2322GQH Inyathelo lokuguqulela phantsi |
| U2 | I-BMI270 yoluvo lwe-IMU | PB1 | IT-1185AP1C-160G-GTR Cofa iqhosha |
| U3 | Imakrofoni yeMP34DT06JTR MEMS | U8 | HS3003 Ukufuma koluvo |
| U7 | BMM150 Magnetometer IC | DL1 | Led L |
| U5 | APDS-9660 Imodyuli ye-Ambient | DL2 | Amandla aKhokelwayo |
| U9 | i-LPS22HBTR iSensom yoxinzelelo lwe-IC |
Ezantsi:
| Ref. | Inkcazo | Ref. | Inkcazo |
| SJ1 | VUSB Jumper | SJ2 | D7 Jumper |
| SJ3 | 3v3 Umtsi | SJ4 | D8 Jumper |
Iprosesa
Eyona Prosesa yiArm® Cortex®-M4F ebaleka ukuya kuthi ga kwi-64MHz. Uninzi lwezikhonkwane zalo zixhunywe kwii-headers zangaphandle, nangona kunjalo ezinye zigcinwe kunxibelelwano lwangaphakathi kunye nemodyuli engenazintambo kunye nebhodi yangaphakathi ye-I2C peripherals (IMU kunye ne-Crypto).
PHAWULA: Ngokuchasene nezinye iibhodi ze-Arduino Nano, izikhonkwane ze-A4 kunye ne-A5 zine-internal pull up and default ukuze zisetyenziswe njenge-I2C Bus ngoko ukusetyenziswa njengamagalelo e-analog akukhuthazwa.
IMU
I-Nano 33 BLE Sense Rev2 ibonelela ngezakhono ze-IMU kunye ne-9-axis, ngokudibanisa i-BMI270 kunye ne-BMM150 ICs. I-BMI270 ibandakanya zombini ii-axis gyroscope ezintathu kunye ne-axis accelerometer emithathu, ngelixa i-BMM150 ikwazi ukuva iinguqu kwintsimi yemagneti kuyo yomithathu imilinganiselo. Ulwazi olufunyenweyo lunokusetyenziselwa ukulinganisa iiparamitha zentshukumo ekrwada ngokunjalo nokufunda koomatshini.
I-LPS22HB (U9) iBarometer kunye neSensom yoBubushushu
I-LPS22HB inzwa yoxinzelelo lwe-IC (U9) ibandakanya zombini i-piezoresistive absolute pressure sensor kunye ne-sensor yobushushu edibeneyo kwi-chip encinci. Inzwa yoxinzelelo (U9) idibanisa kunye ne-microcontroller engundoqo (U1) nge-interface ye-I2C. Isixhobo sovayo senziwe nge-micromachined enqunyanyisiwe inwebu yokulinganisa uxinzelelo olupheleleyo, kwaye ibandakanya ibhulorho ye-Wheatstone ngaphakathi yokulinganisa izakhi ze-piezoresistive. Ukuphazamiseka kwamaqondo obushushu kubuyekezwa ngesixhobo sokwenza ubushushu esibandakanyiweyo kwi-chip. Uxinzelelo olupheleleyo lunokuvela kwi-260 ukuya kwi-1260 hPa. Idatha yoxinzelelo inokuvotelwa nge-I2C ukuya kuthi ga kwii-bits ze-24, ngelixa idatha yeqondo lokushisa inokuthi ifakwe kwi-polled ukuya kwi-16-bits. Ithala leencwadi le-Arduino_LPS22HB libonelela ngokulungele ukusetyenziswa kweprotocol ye-I2C ngale chip.
I-HS3003 (U8) i-Humidity ehambelanayo kunye ne-Temperature Sensor
I-HS3003 (U8) yi-sensors ye-MEMS, eyenzelwe ukubonelela ngokufunda ngokuchanekileyo umswakama ohambelanayo kunye nobushushu kwiphakheji encinci. Ukushisa-imbuyekezo kunye nokulinganisa kwenziwa kwi-chip, ngaphandle kokufuna ukujikeleza kwangaphandle. I-HS3003 inokulinganisa ukufuma okuhambelanayo ukusuka kwi-0% ukuya kwi-100% RH kunye namaxesha okuphendula ngokukhawuleza (ngaphantsi kwe-4 imizuzwana). Isivamvo sobushushu esifakwe kwi-chip (esisetyenziselwa imbuyekezo) sinokuchaneka kobushushu obuyi-±0.1 °C. I-U8 inxibelelana nge-microcontroller engundoqo ngebhasi ye-I2C.
Ukufunyanwa Kwezandla
Ukufunyanwa kwentshukumo kusebenzisa iifotodiode ezine zalathiso ukuva amandla e-IR abonakalisiweyo (afunyanwa yi-LED edibeneyo) ukuguqula ulwazi lwentshukumo ebonakalayo (okt isantya, icala kunye nomgama) kulwazi lwedijithali. I-architecture ye-injini ye-gesture ine-activation ngokuzenzekelayo (esekelwe kwiziphumo ze-injini ye-Proximity), ukukhupha ukukhanya kwe-ambient, ukucinywa kwentetho enqamlezileyo, abaguquli bedatha ye-8-bit, ukulibaziseka kokuguqula amandla, i-32-dataset ye-FIFO, kunye nonxibelelwano lwe-I2C oluqhutywa luphazamise. I-injini ye-gesture ithatha uluhlu olubanzi lweemfuno zentshukumo yesixhobo esiphathwayo: iintshukumo ezilula UP-PHANSI-EKUNXELE-EKUNXELE okanye izijekulo ezintsonkothileyo zinokuvakala ngokuchanekileyo. Ukusetyenziswa kwamandla kunye nengxolo kuncitshiswe ngokuhlengahlengiswa kwexesha le-IR LED.
Ukufunyaniswa okukufutshane
Uphawu lokubona ukuba Mfutshane lubonelela ngomlinganiselo womgama (Umzekelo, isikrini sesixhobo esiphathwayo ukuya endlebeni yomsebenzisi) ngokufunyaniswa kwefotodiode yamandla e-IR abonakalisiweyo (afunyanwa yi-LED edibeneyo). Ukuqaphela/ukukhupha iziganeko ziyaqhutywa, kwaye zenzeke nanini na xa isiphumo sokusondele sinqumla useto oluphezulu kunye/ okanye olusezantsi lomqobo. I-injini yokusondela ibonakalisa iirejista zohlengahlengiso lwe-offset ukuze kuhlawulwe i-system offset ebangelwa yi-IR engafunekiyo ebonisa amandla avela kwi-sensor. I-IR LED intensity yifektri ilungiswe ukuphelisa imfuno yokulinganisa izixhobo zokuphela ngenxa yeenguqu zecandelo. Iziphumo ezikufutshane ziphuculwa ngakumbi ngokuthabatha ukukhanya okuzenzekelayo.
Ukubona umbala kunye ne-ALS
Uphawu loMbala kunye ne-ALS yokufumanisa inika idatha ebomvu, eluhlaza, eluhlaza okwesibhakabhaka kunye nokukhanya okucacileyo. Ngalinye itshaneli ze-R, G, B, C zine-UV kunye ne-IR yokuthintela isihluzi kunye ne-converter yedatha ezinikeleyo evelisa idatha ye-bit ye-16 ngaxeshanye. Olu lwakhiwo luvumela ii-aplikeshini ukuba zilinganise ngokuchanekileyo ukukhanya kwe-ambient kunye nombala wengqiqo ovumela izixhobo ukubala ubushushu bombala kunye nokulawula isikhanyiso sokungasemva.
Imakrofoni yedijithali
I-MP34DT06JTR i-ultra-compact, i-low-power, i-omnidirectional, i-microphone ye-MEMS yedijithali eyakhelwe nge-capacitive sensing element kunye ne-interface ye-IC. Into yokuva, ekwaziyo ukubona amaza e-acoustic, yenziwa kusetyenziswa inkqubo ekhethekileyo yesilicon micromachining ezinikele ekuveliseni izinzwa zomsindo.
Umthi wamandla
Ibhodi inokunikwa amandla nge-USB connector, VIN okanye VUSB izikhonkwane kwi headers.
ilivo
PHAWULA: Kuba i-VUSB isondla i-VIN nge-Schottky diode kunye nomlawuli we-DC-DC ochaze ubuncinane bomthamo wegalelo.tage yi 4.5V eyona volthi mincinci yonikezelotage ukusuka kwi-USB kufuneka inyuswe ibe yivoltage kuluhlu oluphakathi kwe-4.8V ukuya kwi-4.96V, kuxhomekeke kumbane owenziweyo.
Ukusebenza kweBhodi
Ukuqalisa – IDE
Ukuba ufuna ukucwangcisa iNano 33 BLE Sense Rev2 yakho ngelixa ungasebenziyo kufuneka ufakele iArduino Desktop IDE [1] Ukuqhagamshela iNano 33 BLE Sense Rev2 kwikhompyuter yakho, uya kudinga intambo ye-USB eyiMicro-B. Oku kunika amandla ebhodini, njengoko kuboniswe yi-LED.
Ukuqalisa-Umhleli weLifu leArduino
Zonke iibhodi zeArduino, kubandakanywa nale, zisebenza ngaphandle kwebhokisi kwi-Arduino Cloud Editor [2], ngokufaka nje iplagin elula.
I-Arduino Cloud Editor ibanjwe kwi-intanethi, ngoko iya kuhlala isexesheni ngeempawu zamva nje kunye nenkxaso yazo zonke iibhodi. Landela [3] ukuqalisa ukubhala ikhowudi kwisikhangeli kwaye ulayishe imizobo yakho ebhodini yakho.
Ukuqalisa-Arduino Cloud
Zonke iimveliso ezinikwe amandla ze-Arduino IoT zixhaswa kwi-Arduino Cloud ekuvumela ukuba ungene, igrafu kwaye uhlalutye idatha yenzwa, uqalise imicimbi, kwaye uzenzele ikhaya lakho okanye ishishini.
Sample Sketches
Sample mizobo yeNano 33 BLE Sense Rev2 inokufumaneka nokuba ku “Eksamples" kwimenyu ye-Arduino IDE okanye kwicandelo elithi "Uxwebhu" lweArduino Docs webindawo.
Izixhobo ezikwi-Intanethi
Ngoku udlule kwizinto ezisisiseko onokuthi uzenze ngebhodi ungaphonononga amathuba angenasiphelo ebonelela ngokujonga iiprojekthi ezinomdla kwi-Arduino Project Hub [4], i-Arduino Library Reference [5] kunye nevenkile ekwi-line apho uya kuba nakho ukugcwalisa ibhodi yakho ngezivamvo, ii-actuator kunye nokunye.
UkuBuyiselwa kweBhodi
Zonke iibhodi zeArduino zine-bootloader eyakhelwe-ngaphakathi evumela ukuba ibhodi ivuleke nge-USB. Kwimeko apho umzobo utshixa iprosesa kwaye ibhodi ayifumaneki kwakhona nge-USB kunokwenzeka ukuba ungene kwimowudi yokuqalisa ngokucofa kabini iqhosha lokuseta kwakhona emva kokunyusa amandla.
Izikhonkwane zoDibaniso
i-USB
| Iphini | Umsebenzi | Uhlobo | Inkcazo |
| 1 | I-VUSB | Amandla | Igalelo loBonelelo lwaMandla. Ukuba ibhodi inikwe amandla nge-VUSB ukusuka kwisihloko esi siPhumo (1) |
| 2 | D- | Ezahlukileyo | Idatha eyahlukileyo ye-USB- |
| 3 | D+ | Ezahlukileyo | Idatha eyahlukileyo ye-USB + |
| 4 | ID | I-Analog | Ikhetha uMamkeli/umsebenzi weSixhobo |
| 5 | GND | Amandla | Umhlaba wamandla |
Iiheader
Ibhodi iveza iziqhagamshelo ezimbini ze-pin ezinokuthi zidityaniswe ngeeheader ze-pin okanye zithengiswe ngee-vias ezidibeneyo.
| Iphini | Umsebenzi | Uhlobo | Inkcazo |
| 1 | D13 | Idijithali | GPIO |
| 2 | +3V3 | Ukuphuma kwamandla | Imveliso yamandla eveliswa ngaphakathi kwizixhobo zangaphandle |
| 3 | I-AREF | I-Analog | Isalathiso seAnalog; ingasetyenziswa njenge GPIO |
| 4 | A0/DAC0 | I-Analog | I-ADC in/DAC iphumile; ingasetyenziswa njenge GPIO |
| 5 | A1 | I-Analog | I-ADC ngaphakathi; ingasetyenziswa njenge GPIO |
| 6 | A2 | I-Analog | I-ADC ngaphakathi; ingasetyenziswa njenge GPIO |
| 7 | A3 | I-Analog | I-ADC ngaphakathi; ingasetyenziswa njenge GPIO |
| 8 | A4/SDA | I-Analog | I-ADC ngaphakathi; I2C SDA; Ingasetyenziswa njenge GPIO (1) |
| 9 | A5/SCL | I-Analog | I-ADC ngaphakathi; I-I2C SCL; Ingasetyenziswa njenge GPIO (1) |
| 10 | A6 | I-Analog | I-ADC ngaphakathi; ingasetyenziswa njenge GPIO |
| 11 | A7 | I-Analog | I-ADC ngaphakathi; ingasetyenziswa njenge GPIO |
| 12 | I-VUSB | Amandla Ngaphakathi/Ngaphandle | Ngokwesiqhelo iNC; inokuqhagamshelwa kwi-VUSB pin yesiqhagamshelo se-USB ngokufutshane i-jumper |
| 13 | RST | Digital In | Ungeniso lokusetha ngokutsha olusebenzayo olusezantsi (iphindiwe yephini 18) |
| 14 | GND | Amandla | Umhlaba wamandla |
| 15 | VIN | Amandla Angaphakathi | Igalelo laMandla eVin |
| 16 | TX | Idijithali | UART TX; ingasetyenziswa njenge GPIO |
| 17 | RX | Idijithali | UART RX; ingasetyenziswa njenge GPIO |
| 18 | RST | Idijithali | Ungeniso lokusetha ngokutsha olusebenzayo olusezantsi (iphindiwe yephini 13) |
| 19 | GND | Amandla | Umhlaba wamandla |
| 20 | D2 | Idijithali | GPIO |
| 21 | D3/PWM | Idijithali | GPIO; ingasetyenziswa njenge PWM |
| 22 | D4 | Idijithali | GPIO |
| 23 | D5/PWM | Idijithali | GPIO; ingasetyenziswa njenge PWM |
| 24 | D6/PWM | Idijithali | GPIO, ingasetyenziswa njenge PWM |
| 25 | D7 | Idijithali | GPIO |
| 26 | D8 | Idijithali | GPIO |
| 27 | D9/PWM | Idijithali | GPIO; ingasetyenziswa njenge PWM |
| 28 | D10/PWM | Idijithali | GPIO; ingasetyenziswa njenge PWM |
| 29 | D11/MOSI | Idijithali | SPI MOSI; ingasetyenziswa njenge GPIO |
| Iphini | Umsebenzi | Uhlobo | Inkcazo |
| 30 | D12/MISO | Idijithali | SPI MISO; ingasetyenziswa njenge GPIO |
Debug
Kwicala elisezantsi lebhodi, phantsi kwemodyuli yonxibelelwano, iimpawu ze-debug zihlelwe njenge-3 × 2 iipadi zokuvavanya kunye ne-100 mil pitch kunye ne-pin 4 esusiwe. I-Pin 1 ibonakaliswe kwi-Figure 3 - Izikhundla ze-Connector
| Iphini | Umsebenzi | Uhlobo | Inkcazo |
| 1 | +3V3 | Ukuphuma kwamandla | Imveliso yamandla eveliswa ngaphakathi iza kusetyenziswa njengevoltage reference |
| 2 | SWD | Idijithali | nRF52480 iDatha yoLungiso lweNcingo olunye |
| 3 | SWCLK | Digital In | nRF52480 Iklokhi yocingo oluNye yokulungisa iimpazamo |
| 5 | GND | Amandla | Umhlaba wamandla |
| 6 | RST | Digital In | Ungeniso lokuseta ngokutsha olusebenzayo olusezantsi |
Ulwazi ngoomatshini
Ulwandlalo lweBhodi kunye neMingxunya yokuNqa
Amanyathelo ebhodi axutywe phakathi kwemetric kunye ne-imperial. Amanyathelo obukhosi asetyenziselwa ukugcina igridi ye-100 mil pitch phakathi kwemigca yezikhonkwane ukuyivumela ukuba ilingane nebhodi yesonka ngelixa ubude bebhodi buMetric.
Iziqinisekiso
Isibhengezo sokuThobela i-CE DoC (EU)
Sibhengeza phantsi koxanduva lwethu ukuba ezi mveliso zingentla zihambelana neemfuno ezingundoqo zale Miqathango ilandelayo ye-EU kwaye ke ngoko sikulungele ukuhamba ngokukhululekileyo kwiimarike ezibandakanya iManyano yaseYurophu (i-EU) kunye noMmandla woQoqosho waseYurophu (EEA).
Isibhengezo sokuThobela kwi-EU RoHS & REACH 211 01/19/2021
Iibhodi ze-Arduino zihambelana ne-RoHS 2 Directive 2011/65/EU yePalamente yaseYurophu kunye ne-RoHS 3 Directive 2015/863/EU yeBhunga le-4 kaJuni 2015 ekuthinteleni ukusetyenziswa kwezinto ezithile ezinobungozi kwisixhobo sombane kunye ne-elektroniki.
| Iziyobisi | Elona qondo liphezulu (ppm) |
| Khokela (Pb) | 1000 |
| I-Cadmium (Cd) | 100 |
| Imercury (HG) | 1000 |
| Hexavalent Chromium (Cr6+) | 1000 |
| Iibiphenyls zePoly Brominated (PBB) | 1000 |
| I-Poly Brominated Diphenyl ethers (PBDE) | 1000 |
| I-Bis(2-Ethylhexyl} phthalate (DEHP) | 1000 |
| I-Benzyl butyl phthalate (BBP) | 1000 |
| I-Dibutyl phthalate (DBP) | 1000 |
| I-Diisobutyl phthalate (DIBP) | 1000 |
Ukukhululwa: Akukho kukhululwa kubangwayo.
Iibhodi ze-Arduino zihambelana ngokupheleleyo neemfuno ezihambelanayo ze-European Union Regulation (EC) 1907 / 2006 malunga noBhaliso, uVavanyo, uGunyaziso kunye nokuThintelwa kweMichiza (REACH). Sibhengeza ukuba akukho nanye kwii-SVHCs (https://echa.europa.eu/web/guest/candidate-list-table), ULuhlu lwabaMviwa beZinto eziNxibelelayo eziPhakeme kakhulu zogunyaziso ngoku olukhutshwe yi-ECHA, lukhona kuzo zonke iimveliso (kunye nephakheji) ngobuninzi obupheleleyo kuxinzelelo olulingana okanye ngaphezulu kwe-0.1%. Ngokolwazi lwethu, sikwabhengeza ukuba iimveliso zethu aziqulathanga naziphi na izinto ezidweliswe “kuLuhlu loGunyaziso” (Isihlomelo XIV semigaqo ye-REACH) kunye nezinto eziXhathayo kakhulu (SVHC) kuyo nayiphi na imali ebalulekileyo njengoko kuchaziwe. ngeSihlomelo XVII soluhlu lwabaMviwa olupapashwe yi-ECHA (i-Arhente yeMichiza yaseYurophu) 1907 /2006/EC.
Ungquzulwano lweZimbiwa isibhengezo
Njengomboneleli wehlabathi jikelele wezinto zombane kunye nezombane, iArduino iyazazi izibophelelo zethu ngokubhekiselele kwimithetho nemimiselo ephathelele kwiConflict Minerals, ngokukodwa iDodd-Frank Wall Street Reform kunye noMthetho woKhuseleko lwaBathengi, iCandelo 1502. IArduino ayiveli ngqo okanye iqhube ukungquzulana ngokuthe ngqo. iiminerali ezifana neTin, iTantalum, iTungsten, okanye iGolide. Iiminerali eziphikisanayo ziqulethwe kwiimveliso zethu ngendlela yesolder, okanye njengenxalenye yealloys zetsimbi. Njengenxalenye yenkuthalo yethu efanelekileyo, i-Arduino iqhagamshelane nabanikezeli becandelo ngaphakathi kwekhonkco lethu lobonelelo ukuze baqinisekise ukuqhubeka kwabo nokuthobela imimiselo. Ngokusekelwe kulwazi esilufumeneyo ukuza kuthi ga ngoku, sibhengeza ukuba iimveliso zethu zinezimbiwa eziNgqubuthelana ezithathwe kwiindawo ezingenazingxabano.
FCC
Isilumkiso seFCC
Naluphi na uTshintsho okanye uhlengahlengiso olungavunywanga ngokucacileyo liqela elinoxanduva lokuthobela lunokuphelisa igunya lomsebenzisi lokusebenzisa isixhobo. Esi sixhobo sithobela inxalenye ye-15 yeMithetho yeFCC. Umsebenzi uxhomekeke kwezi meko zimbini zilandelayo:
- Esi sixhobo sisenokungabangeli uphazamiseko oluyingozi
- Esi sixhobo kufuneka samkele naluphi na uphazamiseko olufunyenweyo, kuquka uphazamiseko olunokubangela usetyenziso olungafunekiyo.
INkcazo yeFCC RF yokuVela kwiMitha:
- Esi siThuthi akufuneki sibe kwindawo enye okanye sisebenze kunye nayo nayiphi na enye i-eriyali okanye isidluliseli.
- Esi sixhobo sithobela imida yokuvezwa kwemitha ye-RF emiselwe indawo engalawulwayo.
- Esi sixhobo kufuneka sifakwe kwaye sisebenze umgama ongaphantsi kwama-20cm phakathi kweradiyetha kunye nomzimba wakho.
Iincwadana zabasebenzisi zezixhobo zerediyo ezikhululwe kwilayisenisi ziya kuqulatha oku kulandelayo okanye isaziso esifanayo kwindawo ecacileyo kwincwadi yomsebenzisi okanye ngenye indlela kwisixhobo okanye zombini. Esi sixhobo sithobela i(s) kwi-RSS yelayisenisi yoShishino lwaseKhanada. Umsebenzi uxhomekeke kwezi meko zimbini zilandelayo:
- Esi sixhobo sisenokungabangeli ukuphazamiseka
- Esi sixhobo kufuneka samkele naluphi na uphazamiseko, kuquka uphazamiseko olunokubangela ukusebenza okungafunekiyo kwesixhobo.
Isilumkiso se-IC SAR:
IsiXhosa Esi sixhobo kufuneka sifakwe kwaye sisebenze kumgama ongaphantsi kwama-20 cm phakathi kweradiyetha kunye nomzimba wakho.
Kubalulekile: Ubushushu obusebenzayo be-EUT abunakudlula i-85℃ kwaye akufanele bube ngaphantsi kwe -40℃.
Ngale ndlela, i-Arduino Srl ibhengeza ukuba le mveliso iyahambelana neemfuno ezibalulekileyo kunye namanye amalungiselelo afanelekileyo oMgaqo ka-2014/53/EU. Le mveliso ivumelekile ukuba isetyenziswe kuwo onke amazwe angamalungu e-EU.
| Iibhendi zokuphindaphinda | Awona mandla emveliso aphezulu (ERP) |
| 863-870Mhz | I-TBD |
Ulwazi lweNkampani
| Igama leKhampani | Arduino Srl |
| Idilesi yeNkampani | Via Andrea Appiani 25 20900 MONZA Italy |
Amaxwebhu ekubhekiswa kuwo
| Isalathiso | Ikhonkco |
| Arduino IDE (Desktop) | https://www.arduino.cc/en/software |
| Arduino Cloud Umhleli | https://create.arduino.cc/editor |
| I-Arduino Cloud Editor-Ukuqalisa | https://docs.arduino.cc/arduino-cloud/guides/editor/ |
| Arduino Project Hub | https://create.arduino.cc/projecthub?by=part&part_id=11332&sort=trending |
| Isalathiso seThala leeNcwadi | https://www.arduino.cc/reference/en/ |
| Iforamu | https://create.arduino.cc/projecthub/Arduino_Genuino/getting-started-with- iarduino-web-umhleli-4b3e4a |
| UNina B306 | https://content.u-blox.com/sites/default/files/NINA-B3_DataSheet_UBX- 17052099.pdf |
| Ithala leencwadi leArduino_LPS22HB | https://github.com/arduino-libraries/Arduino_LPS22HB |
| Ithala leencwadi leArduino_APDS9960 | https://github.com/arduino-libraries/Arduino_APDS9960 |
Imbali yohlaziyo
| Umhla | Uhlaziyo | Iinguqu |
| 25/04/2024 | 5 | Ikhonkco elihlaziyiweyo kwi-Cloud Editor entsha |
| 03/05/2023 | 4 | Yongeza i-SKU yoguqulelo olunezihloko |
| 10/11/2022 | 3 | Ihlaziywe kwi-akhawunti yeenguqu ze-Rev2: LSM9DS1 -> BMI270+Bmm150, HTS221 -> HS3003, MPM3610 -> MP2322, PCB ukuguqulwa |
| 03/08/2022 | 2 | Amaxwebhu ezalathiso adibanisa uhlaziyo |
| 27/04/2021 | 1 | Uhlaziyo lwedatha gabalala |
Ii-FAQs
- Umbuzo: Ngaba ibhodi inokunikwa amandla ngebhetri?
- A: I-Nano 33 BLE Sense Rev2 ayinayo itshaja yebhetri kodwa inokunikwa amandla nge-USB okanye ngeeheader.
- Q: Uthini umthamo wokusebenza ocetyiswayotage ibhodi?
- A: Ibhodi ixhasa 3.3VI / Os kuphela kwaye ayinyamezeli imiqondiso 5V.
Amaxwebhu / Izibonelelo
 |
I-Arduino ABX00069 Nano 33 BLE Sense Rev2 3.3V AI iBhodi enikwe amandla [pdf] Incwadi yokusebenzisa ABX00069, ABX00070, ABX00069 Nano 33 BLE Sense Rev2 3.3V AI Ibhodi enikwe amandla, ABX00069, Nano 33 BLE Sense Rev2 3.3V AI IBhodi eVunyiweyo, iBhodi yeBLE Sense Rev2 3.3V inikwe amandla, iBhodi ye-AI inikwe amandla, |