UM3099
Incwadi yokusebenzisa
Uyisebenzisa njani iStellarLINK
Intshayelelo
I-StellarLINK yi-debugger ye-circuit / programmer kwiintsapho ze-Stellar microcontrollers kunye neentsapho ze-microcontroller ze-SPC5x.
Phawula: umfanekiso awungowesivumelwano.
Ngaphezuluview
I-adapter ye-StellarLINK yi-USB/JTAG i-debugger dongle yezixhobo zeStellar kunye nezixhobo ze-SPC5x. Iyahambelana ne-IEEE 1149.1 JTAG iprotocol.
I-adapter ye-StellarLINK yenza ukuba isicelo siqhutywe kunye nokulungiswa kweebhodi kwiibhodi zeStellar kunye neebhodi ze-SPC5x kwaye zibonelela ngeprogram ye-NVM (cima / inkqubo / uqinisekise).
Isivumelwano selayisensi
Ukupakishwa kwale bhodi yovavanyo kwatywinwa ngotywino oluchazayo, ngokwaphula eli tywina, uyavumelana nemigaqo nemiqathango yesivumelwano selayisenisi yebhodi yovavanyo, imiqathango nemiqathango efumaneka apha https://www.st.com/resource/en/evaluation_board_terms_of_use/evaluationproductlicenseagreement.pdf.
Ekuqhawukeni kwesitywina, wena kunye ne-STMicroelectronics nengene kwisivumelwano selayisenisi yebhodi yovavanyo, ikopi yaso nayo ifakwe kwibhodi yovavanyo ukwenzela ukuba kube lula.
Ingqalelo: Le bhodi yovavanyo inikezela kuphela ngeempawu ezilinganiselweyo zokuvavanya iimveliso ze-ST. Ayikavavanywa ukuba isetyenziswe kunye nezinye iimveliso kwaye ayifanelekanga naluphi na ukhuseleko okanye esinye isicelo sorhwebo okanye umthengi. Le bhodi yovavanyo ngenye indlela ibonelelwe ngokuthi “NJENGOKO ZINJALO” kwaye i-STMicroelectronics iyazikhupha zonke iziqinisekiso, ezichaziweyo okanye ezichaziweyo, kubandakanywa iziqinisekiso ezichaziweyo zokurhwebelana kunye nokufaneleka kwenjongo ethile.
Ukuphatha izilumkiso
Nceda uqaphele ukuphatha umxholo wephakheji ukuze uthintele ukukhutshwa kwe-electrostatic.
Ngaphambi kokuba i-EVB isetyenziswe okanye kusetyenziswe amandla, nceda ufunde ngokupheleleyo la macandelo alandelayo malunga nendlela yokuqwalasela ngokuchanekileyo ibhodi. Ukungaphumeleli ukuqwalasela kakuhle ibhodi kunokubangela icandelo elingenakulungiseka, umonakalo we-MCU okanye we-EVB.
Inkcazo yehardware
4.1 Iimpawu ze-Hardware
I-StellarLINK inezi mpawu zilandelayo:
- USB/JTAG debugger dongle
- Amandla e-5 V anikezelwe sisidibanisi se-USB esincinci
- Yenza ukuba usetyenziso luqhutywe kunye nolungiso lweempazamo kwizixhobo zeStellar nakwizixhobo ze-SPC5x
- Iyahambelana ne-IEEE 1149.1 JTAG iprotocol
- Idibanisa uqhagamshelo lwe-serial port ngojongano lwe-USB (virtual COM)
- Ibonelela ngenkqubo ye-NVM (cima/inkqubo/qinisekisa)
- Iziqhagamshelo:
-I-20-pin ye-Arm® isidibanisi sika-JTAG/Ujongano olungundoqo lweDAP
-I-10-pin yesiqhagamshelanisi esisentloko kaJTAG/Ujongano olungundoqo lweDAP
-I-14-pin yesiqhagamshelanisi esisentloko kaJTAG ujongano
-Izikhonkwane ezi-3 zentloko yokudibanisa kujongano lwe-UART - Ubume be-LED ukubonisa umthamo we-IO wethagethitage, imo yodibaniso, kunye nemo yokuqhuba
- Iqondo lokushisa elisebenzayo: ukusuka kwi-0 ukuya kwi-50 °C
IZIXHOBO EZINXULUMENEYO
5 Ulungelelwaniso lweHardware kwiphepha lesi-7
4.2 Imilinganiselo ye-Hardware
I-StellarLINK inemilinganiselo elandelayo:
- Ubungakanani bebhodi: 54 mm x 38 mm x 15 mm
Ubumbeko lwe-Hardware
I-StellarLINK yi-adapter ye-USB esekelwe kwi-chip interface ye-FTDI FT2232HL.
Umsebenzisi we-EEPROM ucwangciswe ngenombolo eyodwa yesiriyeli.
5.1 Iziqhagamshelo
Itheyibhile elandelayo ichaza izixhumi ezikhoyo kwibhodi yeStellarLINK.
Itheyibhile 1. Izihlanganisi
| Isidibanisi | Inkcazo | Isikhundla |
| P1 | Mini-USB isinxibelelanisi female | Icala eliphezulu A2 |
| SWJ1 | I-10-pin yesiqhagamshelanisi esisentloko ka-JTAG/Ujongano olungundoqo lweDAP | Icala eliphezulu A3 |
| CN1 | I-14-pin yesiqhagamshelanisi esisentloko ka-JTAG ujongano | Icala eliphezulu D2-D3 |
| CN2 | Isidibanisi esinesihloko esi-3 sojongano lwe-UART | Icala eliphezulu D1 |
| CN3 | I-20-pin Isidibanisi seArm sika-JTAG/Ujongano olungundoqo lweDAP | Icala eliphezulu B4-C4 |
Lo mfanekiso ulandelayo ubonisa indawo yezixhumi ezikhoyo kwi-adapter ye-StellarLINK.
IZIXHOBO EZINXULUMENEYO
6 Uyilo phezuview kwiphepha 11
7 BOM kwiphepha le-13
5.1.1 SWJ1
Le theyibhile ilandelayo ichaza i-SWJ1 pinout.
Uluhlu 2. SWJ1 pinout
| Iphini | Inkcazo |
| 1 | VIN |
| 2 | TMS |
| 3 | GND |
| 4 | TCK |
| 7 | GND |
| 5 | GND |
| 6 | TDO |
| 8 | TDI |
| 9 | GND |
| 10 | I-SRST |
IZIXHOBO EZINXULUMENEYO
7 BOM kwiphepha le-13
5.1.2 CN1
Le theyibhile ilandelayo ichaza i-CN1 pinout.
| Iphini | Inkcazo |
| 1 | TDI |
| 2 | GND |
| 3 | TDO |
| 4 | GND |
| 7 | TCK |
| 5 | GND |
| 6 | USERID 0 |
| 8 | USERID 1 |
| 9 | SRST# |
| 10 | TMS |
| 11 | VIN |
| 12 | NC |
| 13 | NC |
| 14 | TRST# |
IZIXHOBO EZINXULUMENEYO
7 BOM kwiphepha le-13
5.1.3 CN2
Le theyibhile ilandelayo ichaza i-CN2 pinout.
Itheyibhile 4. CN2 pinout
| Iphini | Inkcazo |
| 1 | UART_RX |
| 2 | UART_TX |
| 3 | GND |
IZIXHOBO EZINXULUMENEYO
7 BOM kwiphepha le-13
5.1.4 CN3
Le theyibhile ilandelayo ichaza i-CN3 pinout.
Itheyibhile 5. CN3 pinout
| Iphini | Inkcazo |
| 1 | VIN |
| 2 | I-NC (ixhoma i-R21 eqhagamshelwe kwi-VIN) |
| 3 | TRSTN |
| 4 | GND |
| 5 | TDI |
| 6 | GND |
| 7 | TMS |
| 8 | GND |
| 9 | TCK |
| 10 | GND |
| 11 | NC |
| 12 | GND |
| 13 | TDO |
| 14 | GND# |
| 15 | SRST# |
| 16 | GND |
| 17 | NC |
| 18 | GND |
| 19 | NC |
| 20 | GND |
IZIXHOBO EZINXULUMENEYO
7 BOM kwiphepha le-13
5.2 LEDs
Itheyibhile elandelayo ichaza izixhumi ezikhoyo kwibhodi yeStellarLINK.
Itheyibhile 6. Ii-LEDs
| Isidibanisi | Inkcazo | Isikhundla |
| D1 | Ukuseta ngokutsha inkqubo ye-LED | Icala eliphezulu D4 |
| D2 | Umsebenzisi we-LED | Icala eliphezulu D4 |
| D3 | Ekujoliswe kuko IO voltagI-LED | Icala eliphezulu D4 |
| D4 | UART Rx LED | Icala eliphezulu A1 |
| D5 | UART Tx LED | Icala eliphezulu A1 |
| D6 | Amandla kwi-LED | Icala eliphezulu A2 |
IZIXHOBO EZINXULUMENEYO
6 Uyilo phezuview kwiphepha 11
7 BOM kwiphepha le-13
5.3 Abatsibayo
Itheyibhile elandelayo ichaza i-jumpers ekhoyo kwibhodi ye-StellarLINK.
Itheyibhile 7. Abatsiba
| Isidibanisi | Inkcazo | Ixabiso elimiselweyo | Isikhundla |
| JP1 | Uqwalaselo lophawu lwethagethi yeTRSTN • I-1-2: Iqhagamshelwe kwi-10K ohm pullup resistor • 1-3: Iqhagamshelwe kwi-TRST esuka kwi-FTDI • 2-3: Iqhagamshelwe kwi-GND |
1-3 | Icala eliphezulu A3 |
IZIXHOBO EZINXULUMENEYO
6 Uyilo phezuview kwiphepha 11
7 BOM kwiphepha le-13
Uyilo ngaphezuluview
BOM
Uluhlu 8. BOM
| # | Into | Qty | Ixabiso | Ukhetho lokunyuswa | Inkcazo | Umkhondo |
| 1 | C1, C3, C7, C8, C9, C10, C11, C12, C13, C14, C15, C17, C19, C21, C22, C23, C24, C25 | 18 | 100nF | I-Capacitor X7R - 0603 | 0603C | |
| 2 | C2, C4 | 2 | 10FF | I-Capacitor X7R - 0603 | 0603C | |
| 3 | C5, C6 | 2 | 12pF | C0G ceramic multilayer capacitor | 0603C | |
| 4 | C16, C18, C20 | 3 | 4μ7 | I-Capacitor X7R - 0603 | 0603C | |
| 5 | CN1 | 1 | Header 7X2 female | Okubhalwe ngasentla kwekhasi, i-7-Pin, umqolo ombini (6+2.5+10mm) | C_EDGE7X2_254 | |
| 6 | CN2 | 1 | Musa ukugcwala | Isinxibelelanisi esisentloko, i-PCB Mount, yakutsha nje, abafowunelwa aba-3, ipini, i-0.1 pitch, i-terminal yomsila we-pc | STP3X1 | |
| 7 | CN3 | 1 | I-ARM20 | Conn Flat Male 20 izikhonkwane, ngqo ephantsi profile | C_EDGE10X2_254 | |
| 8 | D1, D2, D3, D6 | 4 | I-KP-1608SGC | I-LED eluhlaza | I-LED_0603 | |
| 9 | D4 | 1 | I-KP-1608SGC | I-LED eluhlaza | I-LED_0603 | |
| 10 | D5 | 1 | I-KP-1608SGC | I-LED eluhlaza | I-LED_0603 | |
| 11 | JP1 | 1 | Intloko 3 × 2 + jumper | Umtsi 4×2.54_Ivaliwe_V | STP3X2_P50_JMP3W | |
| 12 | L1, L2, L3, L4 | 4 | 74279267 | Ferrite bead 0603 60Ohm 500mA | 0603 | |
| 13 | P1 | 1 | Izibuko le-USB_B | USB-MINI_B | HRS_UX60SC-MB-5S8 | |
| 14 | I-R1, i-R11, i-R18, i-R21 | 4 | 0R | Musa ukugcwala | Isixhasi 0603 | 0603R |
| 15 | I-R2, i-R3 | 2 | 10R | Isixhasi 0603 | 0603R | |
| 16 | R4 | 1 | 1k | Isixhasi 0603 | 0603R | |
| 17 | R5 | 1 | 12k | Isixhasi 0603 | 0603R | |
| 18 | I-R6, i-R7 | 2 | Res ifilimu eshinyeneyo 0603 470 ohm 1% 1/4W | 0603R | ||
| 19 | I-R8, i-R9, i-R14, i-R16, i-R17 | 5 | 4k7 | Isixhasi 0603 | 0603R | |
| 20 | I-R10 | 1 | 2k2 | Isixhasi 0603 | 0603R | |
| 21 | I-R12, i-R13, i-R15, i-R22 | 4 | 470 | Isixhasi 0603 | 0603R | |
| 22 | I-R19, i-R24 | 2 | 0R | Isixhasi 0603 | 0603R |
| # | Into | Qty | Ixabiso | Ukhetho lokunyuswa | Inkcazo | Umkhondo |
| 23 | I-R20, i-R23 | 2 | 10k | Isixhasi 0603 | 0603R | |
| 24 | SWJ1 | 1 | SAM8798-ND | Debug isinxibelelanisi 5×2 1.27mm | SAMTEC_FTSH-105-01-LD | |
| 25 | TP1 | 1 | 90120-0921 | Musa ukugcwala | Iiheader | TP |
| 26 | TP2 | 1 | 90120-0921 | Musa ukugcwala | Iiheader | TP |
| 27 | TVS1, TVS2, TVS3, TVS4, TVS5, TVS6, TVS7, TVS8, TVS9 | 9 | 5.0V | ESD suppressor WE- VE, Vdc=5.0V | I-SOD882T | |
| 28 | U1 | 1 | FT2232HL | FT2232HL | TQFP50P1000X1000X100-64N | |
| 29 | U2 | 1 | USBLC6-2P6 | Ukhuseleko lwe-ESD | SOT666 | |
| 30 | U3 | 1 | I-LD1117S33TR | Ukwehla okuphantsi kwevolthi elungileyotagUmlawuli | SOT223 | |
| 31 | U4 | 1 | I-M93S46XS | I-1K (x16) i-serial microwire bus EEPROM enokhuseleko lweBlock | SO-8 | |
| 32 | U5, U6, U7 | 3 | I-SN74LVC2T45DCTR | Dual-Bit dual-bone transceiver yebhasi | SM8 | |
| 33 | u8, u9 | 2 | I-SN74LVC1T45DCK | I-Single-Bit ye-dual-bone transceiver yebhasi | SOT563 | |
| 34 | U8A, U9A | 2 | SC70-6 | |||
| 35 | X1 | 1 | 12 MHz | Iikristale ze-ECS 12MHz, CL 12,TOL +/-25 ppm, STAB +/-30 ppm,-40 +85 C,ESR 150O |
I-ECS-120-12-36-AGN-TR3 |
Amaqhinga
Imbali yohlaziyo
Uluhlu 9. Imbali yohlaziyo loxwebhu
| Umhla | Uhlaziyo | Iinguqu |
| 07-Nov-2022 | 1 | Ukukhutshwa kokuqala. |
| 20-Feb-2023 | 2 | Inqanaba lokugcinwa kwemfihlo litshintshile ukusuka kuthintelo ukuya kuluntu. |
ISAZISO ESIBALULEKILEYO – FUNDA NGOKUQAPHELELEYO
I-STMicroelectronics NV kunye ne-subsidiaries yayo ("ST") inelungelo lokwenza utshintsho, izilungiso, iziphuculo, ukuguqulwa, kunye nokuphuculwa kweemveliso ze-ST kunye / okanye kolu xwebhu nangaliphi na ixesha ngaphandle kwesaziso. Abathengi kufuneka bafumane ulwazi lwamva nje olufanelekileyo kwiimveliso ze-ST ngaphambi kokubeka iiodolo. Iimveliso ze-ST zithengiswa ngokuhambelana nemigaqo ye-ST kunye neemeko zokuthengisa kwindawo ngexesha lokuvuma umyalelo.
Abathengi banoxanduva kuphela lokhetho, ukhetho, kunye nokusetyenziswa kweemveliso ze-ST kwaye i-ST ayithathi tyala loncedo lwesicelo okanye uyilo lweemveliso zabathengi.
Akukho layisensi, echaziweyo okanye echaziweyo, kulo naliphi na ilungelo lepropathi enomgangatho ophezulu wokuqonda linikezelwa ngu-ST apha.
Ukuthengiswa kwakhona kweemveliso ze-ST ezinamalungiselelo ahlukileyo kulwazi oluchazwe apha kuya kuphelisa nayiphi na iwaranti enikwe yi-ST yaloo mveliso. I-ST kunye ne-logo ye-ST ziimpawu zorhwebo ze-ST. Ngolwazi olongezelelweyo malunga neempawu zentengiso ze-ST, bhekisa ku www.st.com/trademarks. Zonke ezinye iimveliso okanye amagama eenkonzo ziyipropati yabanini bazo.
Ulwazi olukolu xwebhu luthatha indawo kwaye luthatha indawo yolwazi olwalunikelwe ngaphambili kulo naluphi na uguqulelo lwangaphambili lolu xwebhu.
© 2023 STMicroelectronics – Onke amalungelo agciniwe
Amaxwebhu / Izibonelelo
 |
ST StellarLINK Circuit Debugger Programmer [pdf] Incwadi yoMnini iStellarLINK Circuit Debugger Programmer, StellarLINK, Circuit Debugger Programmer, Debugger Programmer, Programmer |
