I-STMicroelectronics ST-LINKV2 kwiSekethe ye-Debugger Programmer
Intshayelelo
I-ST-LINK/V2 yi-debugger ye-in-circuit/programmer ye-STM8 kunye ne-STM32 microcontrollers. Imodyuli yojongano lwecingo olunye (SWIM) kunye neJTAG/ i-serial wire debugging (SWD) ujongano luququzelela unxibelelwano kunye nayo nayiphi na i-STM8 okanye i-STM32 microcontroller esebenza kwibhodi yesicelo.
Ukongeza ekunikezeni imisebenzi efanayo ye-ST-LINK / V2, i-ST-LINK / V2 ISOL ibonisa ukuhlukaniswa kwedijithali phakathi kwePC kunye nebhodi yesicelo esijoliswe kuyo. Ikwamelana nomthamotages ukuya kuthi ga kwi-1000 VRMS.
Ujongano olupheleleyo lwe-USB lwenza unxibelelwano nePC kunye:
- Izixhobo ze-STM8 nge-ST Visual Development (STVD) okanye i-ST Visual Programme (STVP) isoftwe (efumaneka kwi-STMicroelectronics)
- Izixhobo ze-STM32 nge-IAR™, i-Keil®, i-STM32CubeIDE, i-STM32CubeProgrammer, kunye ne-STM32CubeMonitor imimandla yophuhliso edibeneyo.
Iimbonakalo
- Amandla e-5 V anikezelwe sisidibanisi se-USB
- USB 2.0 isantya esipheleleyo esihambelanayo ujongano
- Umgangatho we-USB osemgangathweni ongu-A ukuya kwintambo encinci ye-B
- Iimpawu ezithile zokuqubha
– 1.65 ukuba 5.5 V isicelo voltage ixhaswa kwi-SWIM interface
-SWIM ezinesantya esisezantsi kunye neendlela ezinesantya esiphezulu ezixhaswayo
-Isantya senkqubo ye-SWIM: 9.7 kunye ne-12.8 Kbytes/s, ngokulandelelanayo, kwisantya esiphantsi kunye nesiphezulu
-Intambo ye-SWIM yoqhagamshelo kwisicelo nge-ERNI ethe nkqo esemgangathweni (ref: 284697 okanye 214017) okanye ethe tye (ref: 214012) isinxibelelanisi
-Intambo ye-SWIM yokudibanisa kwisicelo nge-header ye-pin okanye i-2.54 mm pitch connector - JTAG/i-serial debugging (SWD) iimpawu ezithile
– 1.65 ukuba 3.6 V isicelo voltagexhaswa kwi-JTAG/I-SWD interface kunye ne-5 V yokunyamezela amagalelo (a)
-JTAG intambo yokuqhagamshela kwi-J eqhelekileyoTAG I-20-pin pitch 2.54 mm isinxibelelanisi
– Ixhasa uJTAG unxibelelwano, ukuya kuthi ga kwi-9 MHz (ehlala ikho: 1.125 MHz)
-Ixhasa i-serial debug (SWD) ukuya kuthi ga kwi-4 MHz (ehlala ikho: 1.8 MHz), kunye nocingo olulandelelanayo viewer (SWV) unxibelelwano, ukuya kuthi ga kwi-2 MHz - Inqaku lohlaziyo lwe-firmware oluxhaswayo (DFU)
- Imo ye-LED, idanyaza ngexesha lonxibelelwano nePC
- 1000 VRMS high isolation voltage (ST-LINK/V2-ISOL kuphela)
- Ubushushu bokusebenza ukusuka ku-0 ukuya kuma-50 °C
Ukuodola ulwazi
Ukuodola i-ST-LINK/V2, bhekisa kwiThebhile yoku-1.
Itheyibhile 1. Uluhlu lweekhowudi zoku-odola
| Ikhowudi yoku-odola | ST-LINK inkcazelo |
| ST-LINK/V2 | Kwi-circuit debugger/umdwelisi |
| ST-LINK/V2-ISOL | I-debugger ye-in-circuit/programmer ene-digital isolation |
a. I-ST-LINK/V2 inokunxibelelana neethagethi ezisebenza ngaphantsi kwe-3.3 V, kodwa ivelisa iimpawu zemveliso kule voltage kwinqanaba. Iithagethi ze-STM32 ziyanyamezela kule over-voltage. Ukuba amanye amacandelo ebhodi ekujoliswe kuyo anengqiqo, sebenzisa i-ST-LINK/V2-ISOL, STLINK-V3MINIE okanye i-STLINK-V3SET ene-adapter ye-B-STLINK-VOLT ukuphepha impembelelo ye-over-voltage isitofu ebhodini.
Imixholo yemveliso
Iintambo ezinikezelweyo ngaphakathi kwemveliso ziboniswe kwi-Figure 2 kunye ne-Figure 3. Zibandakanya (ukusuka kwesobunxele ukuya kwesokudla):
- Intambo ye-USB esemgangathweni ukusuka ku-A ukuya kwintambo encinci ye-B (A)
- ST-LINK/V2 debugging kunye neprogramming (B)
- Isidibanisi se-SWIM esibiza ixabiso eliphantsi (C)
- Iribhoni ye-SWIM ethe tyaba eneqhagamshelo elisemgangathweni le-ERNI kwelinye icala (D)
- JTAG okanye i-SWD kunye ne-SWV iribhoni ecaba ene-20-pin isiqhagamshelanisi (E)
Ubumbeko lwe-Hardware
I-ST-LINK/V2 yenzelwe malunga nesixhobo se-STM32F103C8, esibandakanya i-Arm® (a) Cortex®-M3 engundoqo yokusebenza okuphezulu. Ifumaneka kwiphakheji ye-TQFP48.
Njengoko kubonisiwe kuMfanekiso 4, i-ST-LINK/V2 ibonelela ngeziqhagamshelo ezimbini:
- Isidibanisi se-STM32 seJTAG/ SWD kunye ne-SWV interface
- isidibanisi se-STM8 sojongano lweSWIM
I-ST-LINK/V2-ISOL ibonelela ngesidibanisi esinye se-STM8 SWIM, STM32 JTAG/SWD, kunye ne-SWV ujongano.
- A = STM32 JTAG kunye ne-SWD target connector
- B = STM8 SWIM isiqhagamshelanisi ekujoliswe kuko
- C = STM8 SWIM, STM32 JTAG, kunye ne-SWD target connector
- D = Umsebenzi wonxibelelwano we-LED
a. IArm luphawu lwentengiso olubhalisiweyo lweArm Limited (okanye iinkampani eziphantsi kwayo) e-US kunye/okanye kwenye indawo.
Uqhagamshelwano ne-STM8
Ukuphuhliswa kwezicelo ezisekelwe kwi-STM8 microcontrollers, i-ST-LINK / V2 inokudibaniswa nebhodi ekujoliswe kuyo ngeentambo ezimbini ezahlukeneyo, kuxhomekeke kwikhonkco ekhoyo kwibhodi yesicelo.
Ezi ntambo zezi:
- Iribhoni ye-SWIM ethe tyaba enekhonkco eliqhelekileyo le-ERNI kwelinye icala
- intambo ye-SWIM ene-4-pin, 2.54 mm izihlanganisi okanye iintambo ze-SWIM ezahlukeneyo
Uqhagamshelwano oluqhelekileyo lwe-ERNI kunye neribhoni ye-SWIM ethe tyaba
Umzobo we-5 ubonisa indlela yokudibanisa i-ST-LINK / V2 ukuba i-ERNI 4-pin ye-SWIM ikhonkco ye-SWIM ikhona kwibhodi yesicelo.
- A = Ibhodi yesicelo ekujoliswe kuyo ene-ERNI isinxibelelanisi
- B = Intambo yocingo ene-ERNI isinxibelelanisi kwelinye icala
- C = STM8 SWIM isiqhagamshelanisi ekujoliswe kuko
- Jonga uMfanekiso 11
Umzobo we-6 ubonisa ukuba i-pin 16 ilahlekile kwi-ST-LINK/V2-ISOL ikhonkco ekujoliswe kuyo. Esi sikhonkwane singekhoyo sisetyenziswa njengesitshixo sokhuseleko kwisidibanisi sentambo, ukuqinisekisa indawo echanekileyo yentambo ye-SWIM kwisidibanisi ekujoliswe kuso nkqu nezikhonkwane, ezisetyenziselwa zombini iSWIM kunye ne-J.TAG iintambo.
Uqhagamshelo lwe-SWIM ngexabiso eliphantsi
Umzobo we-7 ubonisa indlela yokudibanisa i-ST-LINK / V2 ukuba i-4-pin, 2.54 mm, i-swim connector yexabiso eliphantsi ikhona kwibhodi yesicelo.
- A = Ibhodi yesicelo ekujoliswe kuyo nge-4-pin, i-2.54 mm, isixhumi esinexabiso eliphantsi
- B = Intambo yocingo ene-4-pin isidibanisi okanye intambo yeentambo ezihlukeneyo
- C = STM8 SWIM isiqhagamshelanisi ekujoliswe kuko
- Jonga uMfanekiso 12
Imiqondiso ye-SWIM kunye noqhagamshelwano
Itheyibhile 2 ishwankathela amagama omqondiso, imisebenzi, kunye neempawu zoqhagamshelwano ekujoliswe kuzo xa usebenzisa intambo yocingo ene-4-pin connector.
Itheyibhile 2. SWIM imidibaniso yeribhoni eflethi ye-ST-LINK/V2
| Inombolo yePin. | Igama | Umsebenzi | Uqhagamshelo ekujoliswe kulo |
| 1 | VDD | I-VCC ekujoliswe kuyo (1) | MCU VCC |
| 2 | IDATHA | QUBHA | Iphini lokuqubha le-MCU |
| 3 | GND | UMHLABA | GND |
| 4 | SETSHENZISWA KHONA | SETSHENZISWA KHONA | MCU RESET pin |
- Umbane ovela kwibhodi yesicelo uqhagamshelwe kwi-ST-LINK/V2 debugging kunye nebhodi yeprogram ukuqinisekisa ukuhambelana komqondiso phakathi kweebhodi zombini.
Itheyibhile 3 ishwankathela amagama omqondiso, imisebenzi, kunye nemiqondiso yoqhagamshelwano ekujoliswe kuyo usebenzisa intambo yeentambo ezahlukeneyo.
Njengoko i-SWIM i-cable-wires cable ineziqhagamshelo ezizimeleyo kuzo zonke izikhonkwane kwelinye icala, kunokwenzeka ukudibanisa i-ST-LINK / V2-ISOL kwibhodi yesicelo ngaphandle kokudibanisa i-SWIM eqhelekileyo. Kule ribhoni caba, zonke iisignali zibhekiswa ngumbala othile kunye neleyibhile ukwenza lula uqhagamshelwano ekujoliswe kulo.
Itheyibhile 3. I-SWIM yoxhumo lwekhebula oluphantsi kweendleko ze-ST-LINK/V2-ISOL
| Umbala | Igama le-cable pin | Umsebenzi | Uqhagamshelo ekujoliswe kulo |
| Bomvu | TVCC | I-VCC ekujoliswe kuyo (1) | MCU VCC |
| Luhlaza | UART-RX | Engasetyenziswanga | Igciniwe (2)
(ayidityaniswanga kwibhodi ekujoliswe kuyo) |
| Luhlaza | IUART-TX | ||
| Lubhelu | IBHODI0 | ||
| Orenji | QUBHA | QUBHA | Iphini lokuqubha le-MCU |
| Mnyama | GND | UMHLABA | GND |
| Mhlophe | QUMELA-RST | SETSHENZISWA KHONA | MCU RESET pin |
- Umbane ovela kwibhodi yesicelo uqhagamshelwe kwi-ST-LINK/V2 debugging kunye nebhodi yeprogram ukuqinisekisa ukuhambelana komqondiso phakathi kweebhodi zombini.
- I-BOOT0, i-UART-TX kunye ne-UART-RX zigcinelwe uphuhliso lwexesha elizayo.
I-TVCC, i-SWIM, i-GND, kunye ne-SWIM-RST inokudibaniswa nexabiso eliphantsi le-2.54 mm i-pitch connector okanye ukukhonkxa iintloko ezikhoyo kwibhodi ekujoliswe kuyo.
Uqhagamshelwano ne-STM32
Ukuphuhliswa kwezicelo ezisekelwe kwi-STM32 microcontrollers, i-ST LINK/V2 kufuneka iqhagamshelwe kwisicelo usebenzisa umgangatho we-20-pin J.TAG Iribhoni ecaba inikezelwe.
Itheyibhile 4 ishwankathela amagama emiqondiso, imisebenzi, kunye nemiqondiso yoqhagamshelwano ekujoliswe kuyo yomgangatho we-20-pin J.TAG iribhoni ethe tyaba.
Uluhlu 4. JTAG/Uqhagamshelwano lweentambo ze-SWD
| Inombolo yePin. | ST-LINK/V2
isinxibelelanisi (CN3) |
ST-LINK/V2
umsebenzi |
Uqhagamshelo ekujoliswe kulo (JTAG) | Uqhagamshelo ekujoliswe kulo (SWD) |
| 1 | VAPP | I-VCC ekujoliswe kuyo | MCU VDD(1) | MCU VDD(1) |
| 2 | ||||
| 3 | I-TRST | JTAG I-TRST | JNTRST | I-GND(2) |
| 4 | I-GND(3) | GND(3) | GND(3)(4) | GND(3)(4) |
| 5 | TDI | JTAG TDO | JTDI | I-GND(2) |
| 6 | GND(3) | GND(3) | GND(3)(4) | GND(3)(4) |
| 7 | TMS_SWDIO | JTAG TMS, SW IO | JTMS | ISWDIO |
| 8 | GND(3) | GND(3) | GND(3)(4) | GND(3)(4) |
| 9 | TCK_SWCLK | JTAG TCK, SW CLK | JTCK | SWCLK |
| 10 | I-GND(5) | GND(5) | GND(4)(5) | GND(4)(5) |
| 11 | Ayidityaniswanga | Ayidityaniswanga | Ayidityaniswanga | Ayidityaniswanga |
| 12 | GND | GND | GND(4) | GND(4) |
| 13 | TDO_SWO | JTAG TDI, SWO | JTDO | TRACESWO(6) |
| 14 | GND(5) | GND(5) | GND(4)(5) | GND(4)(5) |
| 15 | I-NRST | I-NRST | I-NRST | I-NRST |
| 16 | GND(3) | GND(3) | GND(3)(4) | GND(3)(4) |
| 17 | Ayidityaniswanga | Ayidityaniswanga | Ayidityaniswanga | Ayidityaniswanga |
| 18 | GND | GND | GND(4) | GND(4) |
| 19 | VDD(3) | I-VDD (3.3 V)(3) | Ayidityaniswanga | Ayidityaniswanga |
| 20 | GND | GND | GND(4) | GND(4) |
- Umbane ovela kwibhodi yesicelo uqhagamshelwe kwi-ST-LINK/V2 debugging kunye nebhodi yeprogram ukuqinisekisa ukuhambelana komqondiso phakathi kweebhodi.
- Qhagamshela kwi-GND yokunciphisa ingxolo kwiribhoni.
- Ifumaneka kwi-ST-LINK/V2 kuphela, ayiqhagamshelwanga kwi-ST-LINK/V2-ISOL.
- Ubuncinci enye yale pin kufuneka idityaniswe phantsi ngokuziphatha okuchanekileyo, kuyacetyiswa ukuba udibanise zonke.
- I-GND kwi-ST-LINK/V2, esetyenziswa yi-SWIM kwi-ST-LINK/V2-ISOL (jonga iThebhile 3).
- Ngokuzikhethela: yocingo lothotho Viewer (SWV) umkhondo.
Umzobo we-9 ubonisa indlela yokudibanisa i-ST-LINK/V2 kwithagethi usebenzisa i-JTAG intambo
- A = Ibhodi yesicelo ekujoliswe kuyo enoJTAG isinxibelelanisi
- B = JTAG/SWD 20-wire flat cable
- C = STM32 JTAG kunye ne-SWD target connector
Isalathiso somdibaniso ofunekayo kwibhodi yesicelo ekujoliswe kuyo yile: 2x10C i-header wrapping 2x40C H3 / 9.5 (pitch 2.54) - HED20 SCOTT PHSD80.
Phawula: Ukusetyenziswa kweendleko eziphantsi, okanye xa umgangatho we-20-pin 2.54 mm-pitch footprint yokudibanisa mkhulu kakhulu, kunokwenzeka ukuphumeza Tag-Qhagamshela isisombululo. I Tag-Ukudibanisa i-adapter kunye nekhebula inikezela ngeendlela ezilula nezithembekileyo zokudibanisa i-ST-LINK/V2 okanye i-ST-LINK/V2-ISOL kwi-PCB ngaphandle kokufuna icandelo lokukhwelana kwi-PCB yesicelo.
Ukufumana iinkcukacha ezithe vetshe kwesi sisombululo kunye nesicelo-PCB-ulwazi lweenyawo, tyelela
www.tag-Connect.com.
Iireferensi zamacandelo ahambelana noJTAG kunye nojongano lwe-SWD zezi:
a) I-adapter ye-TC2050-ARM2010 (i-20-pin- ukuya kwi-10-pin-interface yebhodi)
b) TC2050-IDC okanye TC2050-IDC-NL (Akukho Imilenze) (10-pin cable)
c) TC2050-CLIP egcina ikliphu ukuze isetyenziswe neTC2050-IDC-NL (ukhetho)
ST-LINK/V2 ubume be-LED
I-LED ebhalwe nge-COM phezulu kwe-ST-LINK/V2 ibonisa isimo se-ST-LINK/V2 (nokuba luhlobo luni loxhulumaniso). Ngeenkcukacha:
- I-LED idanyaza RED: ubalo lokuqala lwe-USB kunye nePC luyenzeka
- I-LED RED: unxibelelwano phakathi kwePC kunye ne-ST-LINK/V2 isekiwe (isiphelo sobalo)
- I-LED iqhwanyaza OKULULUHLAZA / RED: idatha iyatshintshwa phakathi kwethagethi kunye nePC
- I-LED LULULU: unxibelelwano lokugqibela luphumelele
- I-LED yi-ORANGE: I-ST-LINK / V2 unxibelelwano kunye nethagethi ayiphumelelanga.
Uqwalaselo lwesoftware
ST-LINK/V2 uphuculo lwe-firmware
I-ST-LINK/V2 ifakela i-firmware yokuphucula indlela yokuphucula i-in-situ nge-port ye-USB. Njengoko i-firmware inokuguquka ngexesha lobomi be-ST-LINK/V2 imveliso (ukusebenza okutsha, ukulungiswa kwe-bug, inkxaso yeentsapho ezintsha ze-microcontroller), kucetyiswa ukuba ngamaxesha athile undwendwele amaphepha anikezelweyo. www.st.com ukuhlala usexesheni ngenguqulelo yamva nje.
Uphuhliso lwesicelo se-STM8
Jonga kwi-ST toolset Pack24 enePatch 1 okanye yakutshanje, equka i-ST Visual Development (STVD) kunye ne-ST Visual Programmer (STVP).
Uphuhliso lwesicelo se-STM32 kunye nenkqubo yeflash
Izixhobo zomntu wesithathu (IAR™ EWARM, Keil® MDK-ARM™) zixhasa i-ST-LINK/V2 ngokweenguqulelo ezinikwe kwiThebhile 5 okanye kwinguqulelo yamva nje ekhoyo.
Itheyibhile 5. Indlela i-toolchains yomntu wesithathu ixhasa ngayo i-ST-LINK/V2
| Iqela lesithathu | Ikhonkco lezixhobo | Inguqulelo |
| IAR™ | EWARM | 6.20 |
| Keil® | MDK-ARM™ | 4.20 |
I-ST-LINK/V2 ifuna umqhubi we-USB ozinikeleyo. Ukuba isethingi yesixhobo ayifaki ngokuzenzekelayo, umqhubi unokufumaneka www.st.com phantsi kwegama STSW-LINK009.
Ngolwazi oluthe kratya malunga nezixhobo zomntu wesithathu, tyelela oku kulandelayo webiindawo:
Amaqhinga
- Ibali leenkcazelo zephini:
VDD = Umthamo ekujoliswe kuwotagingqiqo
IDATHA = SWIM DATA umgca phakathi kwethagethi kunye nesixhobo sokulungisa ingxaki
GND = Umthamo womhlabatage
UKUSETHA kwakhona = Ukusetha ngokutsha inkqubo ekujoliswe kuyo
- Ibali leenkcazelo zephini:
VDD = Umthamo ekujoliswe kuwotagingqiqo
IDATHA = SWIM DATA umgca phakathi kwethagethi kunye nesixhobo sokulungisa ingxaki
GND = Umthamo womhlabatage
UKUSETHA kwakhona = Ukusetha ngokutsha inkqubo ekujoliswe kuyo
Imbali yohlaziyo
Uluhlu 6. Imbali yohlaziyo loxwebhu
| Umhla | Uhlaziyo | Iinguqu |
| 22-Epr-2011 | 1 | Ukukhutshwa kokuqala. |
| 03-Juni-2011 | 2 | Itheyibhile 2: SWIM imidibaniso yeribhoni ecaba ye-ST-LINK/V2: umbhalo osemazantsi wongeziweyo 1 kumsebenzi othi "Target VCC".
Uluhlu 4: JTAG/Uqhagamshelwano lweentambo ze-SWD: ukongeza umbhalo osemazantsi kumsebenzi othi "Target VCC". Itheyibhile 5: Njani Iqela lesithathu izixhobo zokusebenza inkxaso ST-LINK/V2: ihlaziywe "iiNguqulelo" ze-IAR kunye neKeil. |
| 19-Aug-2011 | 3 | Kongezwe iinkcukacha zomqhubi we-USB kwi Icandelo loku-5.3. |
| 11-May-2012 | 4 | Yongezwe i-SWD kunye ne-SWV ku-JTAG iimpawu zoqhagamshelwano. Ilungisiwe |
| 13-Sep-2012 | 5 | Kongezwe ikhowudi yoku-odola ye-ST-LINK/V2-ISOL.
Ihlaziyiwe Icandelo 4.1: Uphuhliso lwesicelo se-STM8 kwiphepha le-15. Inqaku elongeziweyo 6 in Uluhlu loku-4. Inqaku elongeziweyo "Ngezicelo zexabiso eliphantsi..." ngaphambili Icandelo 3.3: ST- LINK/V2 isimo se-LEDs kwiphepha le-14. |
| 18-Oct-2012 | 6 | Yongeziwe Icandelo 5.1: ST-LINK/V2 uphuculo lwe-firmware kwiphepha le-15. |
| 25-Mar-2016 | 7 | Ixabiso leVRMS elihlaziyiweyo Intshayelelo kwaye kwi Iimbonakalo. |
| 18-Oct-2018 | 8 | Ihlaziyiwe Uluhlu 4: JTAG/Uqhagamshelwano lweentambo ze-SWD nemibhalo yayo esemazantsi. Ukuhlelwa okubhaliweyo okuncinci kulo lonke uxwebhu. |
| 09-Jan-2023 | 9 | Ihlaziyiwe Intshayelelo, Iimbonakalo, kwaye Icandelo 5.3: isicelo se-STM32 uphuhliso kunye nenkqubo edanyazayo.
Ihlaziyiwe Itheyibhile 5: Indlela i-toolchains yomntu wesithathu exhasa ngayo i-ST-LINK/V2. Ukuhlelwa okubhaliweyo okuncinci kulo lonke uxwebhu. |
ISAZISO ESIBALULEKILEYO – FUNDA NGOKUQAPHELELEYO
I-STMicroelectronics NV kunye ne-subsidiaries yayo ("ST") inelungelo lokwenza utshintsho, izilungiso, ukuphuculwa, ukuguqulwa, kunye nokuphuculwa kweemveliso ze-ST kunye / okanye kolu xwebhu nangaliphi na ixesha ngaphandle kwesaziso. Abathengi kufuneka bafumane ulwazi lwamva nje olufanelekileyo malunga
Iimveliso ze-ST ngaphambi kokubeka ii-odolo. Iimveliso ze-ST zithengiswa ngokuhambelana nemigaqo ye-ST kunye neemeko zokuthengisa kwindawo ngexesha lokuvuma umyalelo.
Abathengi banoxanduva kuphela lokhetho, ukhetho, kunye nokusetyenziswa kweemveliso ze-ST kwaye i-ST ayithathi tyala loncedo lwesicelo okanye uyilo lweemveliso zabathengi.
Akukho layisensi, echaziweyo okanye echaziweyo, kulo naliphi na ilungelo lepropathi enomgangatho ophezulu wokuqonda linikezelwa ngu-ST apha.
Ukuthengiswa kwakhona kweemveliso ze-ST ezinamalungiselelo ahlukileyo kulwazi oluchazwe apha kuya kuphelisa nayiphi na iwaranti enikwe yi-ST yaloo mveliso.
I-ST kunye ne-logo ye-ST ziimpawu zorhwebo ze-ST. Ngolwazi olongezelelweyo malunga neempawu zentengiso ze-ST, bhekisa ku www.st.com/trademarks. Zonke ezinye iimveliso okanye amagama eenkonzo ziyipropati yabanini bazo.
Ulwazi olukolu xwebhu luthatha indawo kwaye luthatha indawo yolwazi olwalunikelwe ngaphambili kulo naluphi na uguqulelo lwangaphambili lolu xwebhu.
© 2023 STMicroelectronics – Onke amalungelo agciniwe
Amaxwebhu / Izibonelelo
 |
I-STMicroelectronics ST-LINK/V2 KwiSekethe ye-Debugger Programmer [pdf] Incwadi yokusebenzisa I-ST-LINK V2 kwiSekethe ye-Debugger Programmer, i-ST-LINK V2, kwiSekethe i-Debugger Programmer, i-Circuit Debugger Programmer, i-Debugger Programmer, uMcwangcisi |
